Home
/
Oki
/
IP-5630
/
User Manual

Oki IP-5630, User Manual, Page: 179 / 265

Share

Page: 179 / 265

Oki IP-5630 User Manual Download Page 179

179

Advanced operations

Move the print start position

Move the print start position (origin), to start printing on your preferred position.
After printing, rewind the roll, and with this function you can print an image in the blank area.

CAUTION

Complete this operation as quickly as possible. Otherwise the print heads may dry, which may cause ink ejection failure. In
such a case perform a cleaning.

1

BACKFEEDING MEDIA…

Rewind the media.

See

Feed or rewind media

on

CAUTION

Rewind the media after the printout has completely
dried. If the media is rewound while the printout is not
sufficiently dry, the printout may be damaged.

2

PRINTER READY
01: PAPER / 1626mm

Press the

Left

button.

3

START ORIGIN SETTING
OK?

Press the

OK

button.

4

ORIGIN SETTING
CARRIAGE IS MOVING

Carriage stops moving.

The carriage moves and the origin setting function is
activated.

5

SET ORIGIN
OK?

,

Move the carriage with the

Left

or

Right

button to the position to be set as the origin.

Align the

s

mark at the bottom left of the carriage cover’s

front panel with the origin of the next printout.

origin

«
...
177
178
179
180
181
...
»

Summary of Contents for IP-5630










































































































































































































































































Reviews:

No comments