Home
/
Oki
/
IP-5630
/
User Manual

Oki IP-5630, User Manual, Page: 159 / 265

Share

Page: 159 / 265

Oki IP-5630 User Manual Download Page 159

159

Advanced operations

Prevent the media from sticking and wrinkling

Decrease the platen suction fan power

The vacuum pressure applied to the media in the printing zone helps to hold the media down on the platen to keep
the distance from media to print heads constant.
When the media sticks to the platen, set the vacuum pressure to LOW. The LOW vacuum pressure is also effective
when your media is very flexible and wrinkles easily.

1

PRINTER READY
01: PAPER / 1626mm

Press the

MENU

button.

2

MENU

2

INFORMATION

Press the

Down

button to select

EDIT MEDIA

PRESETS

.

3

MENU

2

EDIT MEDIA PRESETS

Press the

OK

button.

4

>EDIT MEDIA PRESETS

2

SELECT PRESET NO.

Press the

Down

button to select

MISC

SETTINGS

.

5

>EDIT MEDIA PRESETS

2

MISC SETTINGS

Press the

OK

button.

6

>>MISC SETTINGS

2

REMAINING MEDIA

Press the

Down

button to select

SUCTION

FAN POWER

.

7

>>MISC SETTINGS

2

SUCTION FAN POWER

Press the

OK

button.

8

>>>SUCTION FAN POWER

2

MEDIUM

Press the

Down

button once.

«
...
157
158
159
160
161
...
»

Summary of Contents for IP-5630










































































































































































































































































Reviews:

No comments