Home
/
Oki
/
IP-5530
/
User Manual

Oki IP-5530, User Manual, Page: 215 / 265

Share

Page: 215 / 265

Oki IP-5530 User Manual Download Page 215

215

Troubleshooting

When an error message is displayed

When the ERROR LED lights up, check the message displayed on the operation panel.
Error messages shown below are classified into two groups.

Service call errors:
Errors that the operator (customer) cannot recover, such as hardware/software failures. Contact your service
representative.

Operator call errors:
Errors that the operator (customer) can recover.

To recover the error, follow the advice described here.

Service call errors

Restart the printer.

If a service call error occurs, restart the printer by turning it off and on as follows. Then the error may be recovered.
(1) Turn off the power switch on the operation panel.
(2) Remove the power cable front he power outlet, and then remove it from the power inlet at the rear of the printer.
(3) Hold the Printer for one minute or more.
(4) Connect each power cord above to its inlet, then connect the two cords to the socket.
(5) Turn on all three switches above.

<System error>

SYSTEM ERROR nnnn
RESTART PRINTER

nnnn: Error code

Meaning

An unrecoverable error occurred.

Action

Contact your service representative, and inform them of the displayed
error code.

«
...
213
214
215
216
217
...
»

Summary of Contents for IP-5530










































































































































































































































































Reviews:

No comments