Home
/
Oki
/
IP-5530
/
User Manual

Oki IP-5530, User Manual, Page: 120 / 265

Share

Page: 120 / 265

Oki IP-5530 User Manual Download Page 120

120

Maintenance

I Sheet mount cleaning

Perform sheet mount cleaning using a head cleaning sheet when the printer displays a message prompting you to
do so. Generally, sheet mount cleaning should be performed approximately once per month.

How long does it take?

The required time for sheet mount cleaning is approximately 1 hour.

Nozzle surface

Cap

<Capping unit>

<Print head>

Note

Do not rub the print heads with a cleaning swab. This may cause the printer to malfunction.

Preparing the sheet mount cleaning

Sheet mount cleaning liquid

Dropper

Cap cleaning sheet

(gray sheet)

Head cleaning sheet

(pink sheet)

Glove

It is recommended to remove the media before executing sheet mount cleaning.

«
...
118
119
120
121
122
...
»

Summary of Contents for IP-5530










































































































































































































































































Reviews:

No comments