Home
/
Oki
/
IP-5530
/
User Manual

Oki IP-5530, User Manual, Page: 117 / 265

Share

Page: 117 / 265

Oki IP-5530 User Manual Download Page 117

117

Maintenance

H Wiper sponge replacement

Replace the wiper sponge with the procedure below when a printer message prompts you to do so. Generally, the
wiper sponge should be replaced approximately once every six month.

1

PRINTER READY
01: PAPER / 1626mm

Press the

MAINTENANCE

button.

2

MAINTENANCE

2

START MAINTENANCE

Press the

DOWN

button to select

WIPER

MAINTENANCE

.

3

MAINTENANCE

2

WIPER MAINTENANCE

Press the

OK

button.

4

WIPER MAINTENANCE

2

REPLACE SPONGE

,

Press the

Down

button to select

REPLACE

SPONGE

, and then press the

OK

button.

5

>REPLACE SPONGE
OK?

Press the

OK

button to start the operation.

To cancel the operation, press the

CANCEL

button.

WIPER IS MOVING...

PLEASE WAIT

6

OPEN COVERS AND
REPLACE WIPER SPONGE

Open the front cover, and then the capping
unit cover.

Maintenance when a message

is displayed

«
...
115
116
117
118
119
...
»

Summary of Contents for IP-5530










































































































































































































































































Reviews:

No comments