manualshive.com logo in svg

Oki C9600hdn, Network And Configuration Manual, Page: 257 / 264

Share
Download
Oki C9600hdn Network And Configuration Manual Download Page 257

 OkiLAN 8200e Network User’s Guide

257

Printer Menu
Boot Menu

To access the Boot Menu:

1. Turn the printer off.
2. Press and hold the 

Enter

 key while turning the printer back on: 

be 

sure to continue holding the Enter key until “Initializing” appears on 
the display.

Parallel Setup

  

Item

Value

Description

Parallel 

Enable

Disable 

Enables/Disables the Centronics 
interface. 

Bi-Direction 

Enable

Disable 

Enables/Disables the bi-directional 
Centronics interface. 

ECP 

Enable

Disable 

Enables/Disables the ECP mode. 

Ack Width 

Narrow

Medium
Wide 

Sets the ACK width for compatible 
reception.  Narrow = 0.5µs. 
Medium = 1.0µs. Wide = 3.0µs 

Ack/Busy 
Timing 

Ack in Busy

 

Ack while Busy 

Sets order to output the BUSY and ACK 
signals for compatible reception. 

I-Prime 3 

microseconds

50 microseconds

Disable

 

Sets the time to enable/disable the 
I-PRIME signal. 

Offline 
Receive 

Enable

Disable

 

When this is set to Enable, the interface 
keeps the receive-possible state even 
when you press the Off-line operating 
panel switch. The interface sends the 
BUSY signal only when the reception 
buffer is full or a service call occurs. 
PS only.

Summary of Contents for C9600hdn









































































































































































































































































Reviews:

No comments