background image

Safety signals

Important information concerning safety is 
distinguished in this manual by the 
following notations:

This Safety alert symbol means: Caution! 
Your safety is involved.

 

!

 WARNING!

Failure to follow warning instructions could 
result in severe or fatal injury to anyone 
working with, inspecting or using the sus-
pension, or to bystanders.

CAUTION!

Caution indicates that special precautions 
must be taken to avoid damage to the 
suspension.

NOTE!

This indicates information that is of impor-
tance with regard to procedures.

Introduction

All of Öhlins advanced suspension products 
are adapted to the brand and model. This 
means that length, travel spring action and 
damping charac teristics, are tested individ-
ually just for the  motorcycle that you have 
decided to fit with Öhlins suspension.

Before installation

Öhlins Racing AB can not be held re spon -
si ble for any damage whatsoever to sus-
 pen sion or  vehicle, or injury to persons, if 
the instruc tions for fitting and main tenance  
are not fol lowed  exactly.  Similarly, the 
 warranty will be come null and void if the 
 instructions are not ad hered to.

!

 

!

 WARNING!

1. Installing a suspension, that is not ap-
 proved by the vehicle man u fac tur er, may 
affect the  stability of your ve hi cle. Öhlins 
Rac ing AB  cannot be held  responsible for 
any per son al in ju ry or dam age what so ev er 
that may oc cur  after fi t ting the sus pen sion. 
 Contact an Öhlins deal er or oth er qual i fi ed 
 person for advice. 

 

 

 

 

 

 

 

2. Please study and make certain that you 
ful ly un der stand all the mount ing in struc tions 
and the owner´s man u als before han dling 
this  suspension kit. If you have any questions 
 regarding proper in stal la tion pro ce dures, 
 contact an Öhlins deal er or other qual i fi ed 
per son. 

    

 

 

 

 

 

3. The vehicle service manual must be 
re ferred to when installing the Öhlins sus-
pension.

NOTE!

 Öhlins products are subject to con tin u al 
improve ment and de vel op ment. Con se -
quent ly, although these in struc tions in clude 
the most up-to-date in for ma tion available 
at the time of print ing, there may be minor 
dif fer enc es between your sus pen sion and 
this manual. Please con sult your Öhlins 
dealer if you have any ques tions with re-
gard to the con tents of the manual.

NOTE!

During storage and transportation, es pe -
cial ly at high ambient tem per a ture, the oil 
and grease used for as sem bling may run 
out inside the pack ing and dam age the ex-
panded pol y sty rene pack ing ma te ri al. This 
is not unusual and is in no way det ri men tal 
to the suspension.

© Öhlins Racing AB.

All rights reserved.

Any reprinting or unauthorized use

without the written permission of

Öhlins Racing AB is prohibited.

Printed in Sweden.

2

Summary of Contents for FG 470

























Reviews: