manualshive.com logo in svg

OHAUS Frontier FC5714, Service Manual, Page: 26 / 43

Share
Download
OHAUS Frontier FC5714 Service Manual Download Page 26

26                                                                                                                 MAINTENANCE 

 

3  MOUNTING SUPPORT 

 

After performing any kind of assembling work, please make sure all the 
grounded contacts are connected correctly! 

 
 

3.1 Replacing the front housing, the incremental shaft encoder and the display 

 
Replacing the front housing

 

 

• Remove the lower covering by turn out the 2 screws (see photo 19). 
 
• Pull the lower edge of the covering away from the mounting plate. 
 
• Pull the covering out of the upper guiding rail. 
 
• Loosen the 5 screws under the control panel and pull away the panel forward. 
 
• Remove the interface cable on the control board.  
  (Connection between control board and control panel). 
 

 

 

 

 

 

 
 
 

 

 

                                                                            

                                                                                      

 

                                                                                                      

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  remove 

Loosen and 

pull away 

forward 

 

Summary of Contents for Frontier FC5714












































Reviews:

No comments