manualshive.com logo in svg

Oerlikon CENTER TWO, Operating Manual

Share
Download
Oerlikon CENTER TWO Operating Manual Download Page 62

Computer interface

GA 09.035/6.02 - 07/2011 - © Oerlikon Leybold Vacuum

61

6.3

Mnemonics

6.3.1

Overview

Mnemonic

Significance

AOM

Analog output mode. Characteristic curve of the 
recorder output.

BAU

Baud rate. Transfer rate of the RS232C interface.

COM

Continuous mode. Continuous transmission of mea-
surements to the serial interface.

COR

Correction factor.

DCD

Display control digits. Number of digits shown in the dis-
play.

DGS

Degas.

ERA

Error relay allocation.

ERR

Error status.

EUM

Switch the emission.

FIL

Filter. Measurement filter.

FUM

Select the filament.

FSR

Full scale range. Full scale range of linear transmitters 
(CTR, DI).

GAS

Gas type correction.

HVC

High vacuum circuit on/off. Switch the high vacuum cir-
cuit of transmitters on/off.

ITR

Read a data string from the ITR/CTR 100/CTR 101 
transmitter.

LOC

Parameter setup lock.

OFC

Offset correction. Offset correction function for linear 
transmitters (CTR).

OFD

Offset display. Offset correction values for linear trans-
mitters (CTR).

PNR

Program number. Firmware version number.

PR1

Pressure sensor 1. Pressure reading of transmitter 1.

PR2

Pressure sensor 2. Pressure reading of transmitter 2.

PR3

Pressure sensor 3. Pressure reading of transmitter 3.

PRE

Pirani range extension.

PRX

Pressure sensors. Pressure readings of all transmitters.

RES

Reset. Reset the serial interface.

Summary of Contents for CENTER TWO







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands