background image

9

Hardware Features

COM1 communication mode DIP switch (SW2)

Open the communication housing case and adjust the DIP switch as follows:

The baud rate is automatically detected and adjusted within the range of 
4800 to 38400 bps. No separate speed setting is required. Once a speed is 
assigned, it is maintained until there is no communication for more than 
one minute. Then, the speed is automatically detected and configured 
again. 

The termination resistance is connected to the end of the communication 
line to remove mutual communication interferences or signal distortions 
that can occur between connected controllers and peripherals.
Use an external connector for termination for COM2 port.

No.

Status

Description

1

Off

Enables RS-232C communication for COM1

On

Enables RS-485 communication for COM1
(Used for hand-held programmer and multi-drop 
connections, etc.)

2

Off

Disables termination for RS-485 communication

On

Enables termination for RS-485 communication

COM1:RS232C/RS485
9pin female D-Sub

24V dc auxiliary output

Panel fixing hole

Battery mounting holder

Input terminal

Expansion unit connector

Status LEDs

LED

Description

RUN

On when processor is in operation.
Flashes when processor is pausing.

PROG

On when the program can be modified or 
downloaded.

ERR

On when processor fault is detected.
Flashes when the battery is not installed 
or needs to be replaced.

COM1
COM2

On when power is supplied normally.
Flashes when communication is 
progressing via the port

Power supply
connector

COM2:
RS232C/RS485
8pin female 
RJ45

DIP switch for COM1
- Selects RS232 or RS485
- Sets termination resistance

Output 
terminals

Operation mode selector switch

Mode

Description

RUN

Processor is in operation. 

Program editing is not allowed.

RMT

Remote control status. 

Run or pause operation, program 

editing and downloading are allowed.

PROG

Processor is in stop mode. 

Program editing is allowed.

IMPORTANT

Summary of Contents for NX7-28ADR


















Reviews: