manualshive.com logo in svg

OCEM LIRE Series, Instruction Manual For Use, Installation And Maintenance

Share
Download
OCEM LIRE Series Instruction Manual For Use, Installation And Maintenance Download Page 12

 

Document UT-MT-0779_EN 

Page 12 of 37 

 

Edition 23/04/2019 

Supersedes edition 06/03/2019 

 

LED INSET RUNWAY EDGE LIGHT LIRE 
INSTRUCTION MANUAL FOR USE, INSTALLATION AND MAINTENANCE 

 

1 

Dome .................................................................................................................... 1 

2 

O-Ring for dome (external) .................................................................................. 1 

3 

O-Ring for dome (internal) ................................................................................... 1 

4 

O-Ring for lower cover ......................................................................................... 1 

5 

Arctic kit heater ................................................................................................ 1-2 

6 

Reflector with hardware ...................................................................................... 4 

7 

LED module with accessories ............................................................................... 4 

8 

Lower cover .......................................................................................................... 1 

9 

Valve for watertightness test ............................................................................... 1 

10 

FAA L-823 plug ................................................................................................. 1-2 

11 

Arctic kit thermostat ........................................................................................ 1-2 

12 

Prism gasket ......................................................................................................... 4 

13 

Prism .................................................................................................................... 4 

14 

Prism holder gasket ............................................................................................. 4 

15 

Mounting plate .................................................................................................... 4 

Figure 6 – Part List 

 

Summary of Contents for LIRE Series






































Reviews:

No comments

Brands by name

Popular brands

Load more brands