Oce VarioPrint 6000 Plus Line Maintenance Manual Download Page 81

Page: 81 / 102

Clean the glue cleaning rollers

CAUTION

Cleaner fluids can cause irritation. Read the Material Safety Data Sheets of the cleaner fluids

before use.

CAUTION

Hot area. Use heat-resistant gloves.

IMPORTANT

Always clean both glue cleaning rollers.

IMPORTANT

For all cleaning actions, apply a small amount of cleaner fluid on an offset pad.

Depending on the kind of pollution, you may require different cleaner solutions.

Procedure

Clean the glue cleaning rollers with Océ Cleaner K.

When the rollers contain white pollution (probably PE-wax), clean the rollers with Océ Cleaner T.

If the rollers show extreme pollution,
• clean the rollers with Océ Cleaner P first and then,
• clean the rollers with Océ Cleaner T.

Clean the rollers again with Océ cleaner K to finish the cleaning procedure.

Carefully remove all the protective paper.

Clean the glue cleaning rollers

Chapter 3 - Maintenance tasks - Level 2

Océ VarioPrint 6000 line

Summary of Contents for VarioPrint 6000 Plus Line







































































































Search results

Summary of Contents for VarioPrint 6000 Plus Line

Reviews:

Related manuals for VarioPrint 6000 Plus Line

Brands by name

Popular brands

Oce VarioPrint 6000 Plus Line, Maintenance Manual

Search results

Summary of Contents for VarioPrint 6000 Plus Line

Reviews:

Related manuals for VarioPrint 6000 Plus Line

Brands by name

Popular brands