manualshive.com logo in svg

Oce ColorWave 500, Operation Manual

Share
Download
Oce ColorWave 500 Operation Manual Download Page 84

Access control and IPsec settings

Introduction

When access control is enabled, you can edit the access control settings.

[Access control] and IPsec settings

Under [Security] - [Configuration] - [Access control], you can set the following settings for each of
the 5 stations:

Setting

Description

[Access control sta-
tion 1]

Enable or disable communication of this host with the printer.

[Access control sta-
tion 1: IPv4 address]

The IPv4 address of the host is allowed to connect to the printer.

[Access control sta-
tion 1: IPv6 address]

The IPv6 address of the host is allowed to connect to the printer.

[IPsec station 1]

Enable or disable IPsec. IPsec is a security protocol that encrypts the
communication between the host and the printer.

[IPsec station 1: Pre-
shared key]

The key for encryption of this host connected via IPsec. If empty, the de-
fault preshared key is used.

For IPsec., you can set the following setting:

Setting

Description

[IPsec default pre-
shared key]

This is the default key for encryption of hosts connected via IPsec. This
key holds for all stations whose preshared key is unspecified.

NOTE

For more details on these settings please consult the Océ PlotWave-ColorWave Systems

Security manual.

Access control and IPsec settings

84

Chapter 3 - Define your Workflow with Océ Express WebTools

Summary of Contents for ColorWave 500











































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands