Oce Arizona 365 GT User Manual Download Page 160

Page: 160 / 234

How to Create a Media for White Ink Print Jobs - ICC

Spot colors are NOT used in ICC processing so continue as usual if you want to create a profile.
To print the ICC swatch:

Procedure

Click > Print Swatch and select your color sampling device.

Click > Setup > Options if you want to choose a larger number of swatches for profile accuracy,
otherwise click > Print.

Click > Read Swatch and read in the ICC data.

Click > Options to modify the settings, or click > Build to use the default build options.

Create a test Print and click > Next to continue.

Click > Finish.

Result

This completes the media profiling workflow and you can now use this media in ONYX
ProductionHouse.

How to Create a Media for White Ink Print Jobs - ICC

160

Chapter 8 - How to Work With White Ink

Summary of Contents for Arizona 365 GT











































































































































































































































Search results

Summary of Contents for Arizona 365 GT

Reviews:

Related manuals for Arizona 365 GT

Brands by name

Popular brands

Oce Arizona 365 GT, User Manual

Search results

Summary of Contents for Arizona 365 GT

Reviews:

Related manuals for Arizona 365 GT

Brands by name

Popular brands