Home
/
Oce
/
Arizona 365 GT
/
User Manual

Oce Arizona 365 GT, User Manual

Share

Page: 111 / 234

background image

How to Change the Height of the Bar

The Ionizer bar is mounted by default to accommodate media up 13mm (0.5 inches) in height. If
you need to use media that has a thickness of greater than 13mm you will have to reverse the
mounting brackets. When the brackets are reversed the maximum thickness of media that can be
used with the ionizer bar is 38mm (1.5 inches).

Procedure

1.

Turn off the printer power switch.

2.

Press down on the ionizer bar first from one end and then the other to release the bar from all
four brackets.

[62] Remove Static Bar

3.

Loosen the bracket mount screw and then slide the bracket up in the keyed slot to remove it.

[63] Bracket Mounted Low

4.

Turn the bracket 180 degrees and then fit the other keyed slot over the bracket screw.

How to Change the Height of the Bar

Chapter 7 - How to Use the Static Suppression Upgrade Kit

111

«
...
109
110
111
112
113
...
»

Summary of Contents for Arizona 365 GT











































































































































































































































Reviews:

No comments

Related manuals for Arizona 365 GT

Brand: Oki Pages: 4

Brand: Nanoptix Pages: 25

Brand: Nanoptix Pages: 4

Brand: YAEN Pages: 4

Brand: Lanier Pages: 234

PS100 - Photo Printer - 50 Sheets

Brand: Olympus Pages: 2

FELIX Pro 3 Touch

Brand: Felix printers Pages: 29

Brand: Riso Pages: 208

PG 2028 SPECIAL

Brand: Olivetti Pages: 104

Brand: SPRT Pages: 48

Brand: Ascend Pages: 6

Brand: Xerox Pages: 284

Brand: Commodore Pages: 188

PRICOM PRICOM C- 5100

Brand: Silex technology Pages: 7

Printpix NC-400D

Brand: FujiFilm Pages: 47

ApeosPort C5570

Brand: Fuji Xerox Pages: 290

Brand: Canon Pages: 76

Brand: Canon Pages: 327

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands