background image

 

 

Copyright 2010-2012 Obihai Technology, Inc. 

54 

-

 

Voice Disconnected: Mobile phone is in a connected call, but the audio stays in the phone instead of going 
to OBiBT 

-

 

0 Active Calls 

-

 

1 Active Call: Mobile phone is in a connected call, with audio going to OBiBT 

 

SP

n

 Service Status (n = 1, 2, 3, 4) 

Note that SP3 and SP4 Service Status are available on the OBi202 and OBi302 only.  The SP

n

 service status values indicate 

the current state of the service with regard to its configuration (or not) and if configured its registration status.  If there are 
problems with the registration or authentication of the OBi with a prescribed service, the SIP 4xx error message will be 
displayed here. This is very useful information for troubleshooting issues with SIP-based services. 
 

OBiTALK Service Status 

The status of the OBiTALK Service includes the following values: 

 

Status – Possible values are: 

-

 

Normal (User Mode): The service is functioning normally 

-

 

Backing Off: The service is currently down; the device is taking a short pause before retrying connection 

 

CallState – Possible values are: 

-

 

N

 Active Calls (where N = 0, 1, .., up to the maximum number of calls allowed in the configuration 

 

OBiPLUS Service Status 

OBiPLUS is a small business collaboration system.  It is an optional service that requires a separate subscription. You may 
subscribe to this service on OBiTALK.com. The administration of this service is described separately in the OBiPLUS 
Administration Guide. 

The status is available on the OBi202 and OBi302 only. The following status values are available: 

 

LicenseState – The state regarding the OBiPLUS Subscription. Possible values are: 

-

 

Service not subscribed 

-

 

Premium Active: Premium level subscription is currently active 

-

 

Basic Active: Basic level subscription is currently active 

-

 

License Expired: Service is not available because your last subscription has expired. 

 
 
LAN Status (OBi202 only) 

The LAN Status page shows the devices currently on the LAN. There are two sections:  

 

Attached Devices: All the devices that the router has discovered on the LAN side; each entry has a MAC address 
and an IP address 

 

DHCP Clients: All the DHCP clients that have an active lease with the DHCP server; each entry has a Client Name, a 
MAC address, an IP address, and the lease expiration time (in seconds) 

 
Below is a screen shot of a typical LAN Status page. This page is available when the OBi202 is working in router mode. 
 

Summary of Contents for OBi110











































































































































































































Reviews: