Obihai OBi110 Administration Manual Download Page 31

Page: 31 / 202

Press # to enter another configuration
selection.

101

Registration State of SP1

The current value will be read back.

Press 0 to repeat the information.

Press # to enter another configuration
selection.

102

SP1 User ID

The current value will be read back.

Press 1 to enter a new value.

Press 2 to set the default value.

Press 0 to repeat the information.

Press # to enter another configuration
selection.

167

SP1 Block Caller ID Enable

Press 1 to enter a new value.

Press 2 to set the default value.

Press 0 to repeat the information.

Press # to enter another configuration
selection.

168

SP1 Block Anonymous Call Enable

Press 1 to enter a new value.

Press 2 to set the default value.

Press 0 to repeat the information.

Press # to enter another configuration
selection.

172

SP1 Call Forward ALL – Enable / Disable

Press 1 to enter a new value.

Press 2 to set the default value.

Press 0 to repeat the information.

Press # to enter another configuration
selection.

173

SP1 Call Forward ALL Number

Press 1 to enter a new value.

Press 2 to set the default value.

Press 0 to repeat the information.

Press # to enter another configuration
selection.

174

SP1 Call Forward on Busy – Enable /
Disable

Press 1 to enter a new value.

Press 2 to set the default value.

Press 0 to repeat the information.

Press # to enter another configuration
selection.

Summary of Contents for OBi110


























































































































































































Search results

Summary of Contents for OBi110

Reviews:

Related manuals for OBi110

Brands by name

Popular brands

Obihai OBi110, Administration Manual

Search results

Summary of Contents for OBi110

Reviews:

Related manuals for OBi110

Brands by name

Popular brands