background image

Oasis SmartChem - INSTALLATION AND OPERATION MANUAL 

 

 

 

 

 

 

Page 

2

 of 

22

 

 

1. 

IMPORTANT WARNINGS & SAFETY INSTRUCTIONS 

IMPORTANT WARNINGS 

This  manual  contains  important  information  about  the  installation,  operation  and  safe  use  of  this 
product. This information should be given to the owner and/or operator of this equipment.  

When  installing  and  using  this  electrical  equipment,  basic  safety  precautions  should  always  be 
followed. Failure to follow safety warnings and instructions in this manual can result in serious injury 
and/or damage to your equipment. Read and follow all warning notices and instructions which are 
included in this manual. 

The Power Supply internally contains live components. There is a danger of electric shock if opened. 
If the power cord is damaged then it should be replaced by the manufacturer, their agent or similar. 

To reduce the risk of injury, 

DO NOT 

 permit young children to use this product unless they have 

been trained by the person responsible for their safety and they acknowledge their ability to use such 
equipment. To reduce the risk of accidents or incidents, service on the unit should only be performed 
by your local pool Professional. 

Ideally, as with all pool equipment, the controller should be installed out of direct weather. The service 
life of the 

Oasis SmartChem 

will be longer if it is not exposed to direct sunlight and rain. 

Before installing, and turning on the 

Oasis SmartChem 

system, take a sample of your Pool/Spa 

water to a pool store and have it tested to ensure that the Pool/Spa system is properly balanced. 
See below for recommended pool chemical ranges; 

CHLORINE: 1 - 3ppm   

pH 7.2 - 7.8 

TOTAL ALKALINITY: 80 - 150 mg/L 

 

CALCIUM HARDNESS: 90 - 300 mg/L 

PHOSPHATE FREE: (0) 

TOTAL DISOLVED SOLIDS: Below 1500ppm 

Always  take  a  sample  of  your  pool  water  away  from  the  return  jets  to  ensure  as  accurate 
reading as possible. 

Always  store  Pool  Chemicals  in  a  well-ventilated  position,  at  least  1.8M  away  from  your  pool 
equipment to prevent fume build-up and causing corrosion of your pool equipment. 

When mixing acid with water, ALWAYS ADD ACID TO WATER. NEVER ADD WATER TO ACID. If 
you add water to acid, it will violently react (creating heat and boiling) and you may be splashed with 
acid. Wear protective equipment such as Gloves and Face Shield when diluting the acid. 

Only use diluted Acid, never use concentrated Acid. ACID should be diluted with water within the 
range of 1 part Acid to 1 part Water (1:1) to 1 part Acid to 2 parts Water (1:2). Dilute the acid in a 
well ventilate area and have running water ready. In case of spillage, wash down area immediately. 
Always seek medical advice if breathing is affected or an Acid Burn occurs. 

NEVER MIX CHEMICALS. Store your pool chemicals in containers that are visibly different by either 
colour and or size. Poisonous Gas can be produced if you mix chemicals. Always store chemicals 
in accordance to the relevant Dangerous Goods Codes and Standards. 

It  is  highly  recommended  that  you  check  your  Water  Chemistry  (especially  the  pH  and  Chlorine 
levels)  regularly,  either  with  a  quality  test  kit  or  at  your  local  pool  store  to  ensure  that  the 

Oasis 

SmartChem 

is working correctly, to ensure there are no malfunctions, and to ensure that the pH and 

ORP sensors are reading correctly. 

It  is  highly  recommended  that  before  you  install  the 

Oasis  SmartChem 

system,  that  you  sit  the 

probe/s in your pool water for 24hrs. This will help the probes to give a more accurate reading from 
the time of installation and will help with the longevity of the probes.

 

 

 

Summary of Contents for SmartChem


























Reviews: