background image

CX Logix Operation MANUAL 

– Updated July 2022 

 

 

 

 

 

 

 

Page 13 of 15 

13.  WARRANTY 

THIS EQUIPMENT HAS BEEN MANUFACTURED AND TESTED TO THE HIGHEST STANDARD 

AND ACCORDINGLY CARRIES THE FOLLOWING WARRANTY. 

 

Your 

Oasis CX Logix 

controller is covered by a 

twelve (12) month

 warranty against defects in 

workmanship and materials if used for its intended purpose and maintained according to instructions.  
 
This warranty is limited to repair or replacement, depending on the problem of the product.  
The customer is liable to return the product to 

Oasis Aquatics

. Please ensure proper packaging so 

that no additional damages occur during transport. 
 
Should you need to lodge a warranty request, ensure to include: 
Product serial number  

Purchase date  

Type of failure/s 

 

 

The Warranty is void under the following circumstances: 

  Water damage from external sources 

  Insect infestation or penetration by dust, sand or other foreign particles inside the controller 

  Equipment that has been misused, neglected, damaged, repaired without authorisation or altered in 

any way 

  Installation is carried out incorrectly by any person other than a person authorised by us to do so 

  Damage beyond our control 

 

 

This  warranty  is  not  transferable  under  any  circumstance.  Keep  your  original  purchase  invoice  and  serial 
number in a safe place. 

Oasis Aquatics

 shall have no liability for incidental or consequential damages. No person is 

authorized to make any representation or warranty on behalf of 

Oasis Aquatics 

other than what is 

stated here. 
This limited warranty is the sole and complete warranty for 

Oasis Aquatics 

and shall be limited to the 

cost of the meter.  

 

 

 

 

Summary of Contents for CX Logix

















Reviews: