manualshive.com logo in svg

O.S. engine MAX-12TR Series, Owner'S Instruction Manual, Page: 12 / 30

Share
Download
O.S. engine MAX-12TR Series Owner'S Instruction Manual Download Page 12

LONG SOCKET WRENCH

Recommended for easy removal 
and replacement of the angled 
and recessed glowplug, the 
O.S.Long Socket Wrench 
incorporates a special grip.

SILICONE FUEL LINE

Heatproof silicone tubing of 
approx. 5mm o.d. and 2mm i.d. 
is required for the connection 
between the fuel tank and 
engine.

CARBURETTOR CONTROLS (10J)

The Needle-Valve:

The Mixture Control Screw:

The Throttle Stop Screw:

For setting the minimum idling speed.

Needle Valve

Mixture Control Valve
Assembly Screw

Throttle Stop Screw

Ball Link

NOTE:
Readjustment may 
be necessary, occa-
sionally to allow for 
changes in fuel for-
mula, gear ratio or 
clutch engagement 
point.

Three adjustable controls are provided on this 
carburettor. 

For adjusting the mixture strength when the throttle 
is fully open.

For adjusting the mixture strength at part-
throttle and idling speeds, to obtain steady 
idling and smooth acceleration to mid speeds.

11

•

•

•

Summary of Contents for MAX-12TR Series































Reviews:

No comments