NXP Semiconductors UM10301 PCA8565 User Manual Download Page 40

Page: 40 / 54

NXP Semiconductors

UM10301

User Manual for PCF85x3, PCF85x63, PCA8565, PCF2123, and

PCA21125

UM10301

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 2.1 — 23 July 2015

40 of 54

•

Access the RTC as little as possible in order to reduce the dynamic current

consumption by the I

C-bus or SPI;

•

Disable the CLKOUT in battery backup mode. If CLKOUT needs to be enabled select

the pull-up resistor as large as possible. However, CLKOUT enabled will dominate

current consumption and severely limit battery backup time;

•

Do not connect the pull-up resistors for the serial interface to V

of the RTC but

connect them to the supply of the rest of the circuit (V

DD1

in Fig 16). This avoids

unnecessary battery current drain from the battery via the pull-up resistors. If in

“Power-Off” everything gets powered down except the RTC, the bus lines will often

not be high impedance. In this case current could run from the battery via the pull-up

resistors and the bus to GND which would severely reduce the possible battery

backup time, if the pull-ups were connected to V

of the RTC;

•

Select the I

C-bus pull-up resistors as large as possible. The value of the pull-up

resistors is a compromise between current consumption and maximum clock

frequency. Lower values result in lower RC time constants and thus faster rise time

of the SCL and SDA lines. Using the I

C-bus, data transfers can be made up to

100 kbit/s in Standard-mode and up to 400 kbit/s in Fast-mode. The corresponding

required maximum rise times are 1 μs for Standard-mode and 300 ns for Fast-mode.

The rise time is a product of bus capacitance and the value of the pull-up resistor.

The bus capacitance is the total capacitance of wire, tracks, connections and pins.

First estimate the capacities. Track capacities can be calculated with the standard

formula for a capacitor. Depending on the PCB material used, values for ε may differ.
For this example a track length of 3 cm is assumed, with a track width of 0.5 mm on

a copper backed 0.7 mm strong PC-board made from FR4 glass epoxy.

0007

0005

−

⋅

Further capacitances are:
Microcontroller pin capacitance C

= 7 pF (assumption)

RTC pin capacitance C

= 7 pF (max value for PCF8563)

Adding these capacitances to the 0.9 pF track capacitance results in a bus

capacitance of 14.9 pF.
Consider the V

related input threshold of V

= 0.7V

and V

= 0.3V

for the

purposed of RC time constant calculation. Then V(t) = V

(1 – e

-t/RC

), where t is the

time since the charging started and RC is the time constant.
V(t1) = 0.3 x V

= V

(1 – e

-t1/RC

); then t1 = 0.3566749 x RC

V(t2) = 0.7 x V

= V

(1 – e

-t2/RC

); then t2 = 1.2039729 x RC

T = t2 – t1 = 0.8473 x RC

The graph in Fig 17 and the equation below show maximum R

as a function of bus

capacitance for Standard-mode, Fast-mode and Fast-mode Plus. For each mode the

P(max)

is a function of the rise time maximum and the estimated bus capacitance C

Summary of Contents for UM10301 PCA8565























































Search results

Summary of Contents for UM10301 PCA8565

Reviews:

NXP Semiconductors UM10301 PCA8565, User Manual, Page: 40 / 54

Search results

Summary of Contents for UM10301 PCA8565

Reviews: