manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 31 System Timer Module (STM)

MPC5602P Microcontroller Reference Manual, Rev. 4

804

Freescale Semiconductor

 

31.6

Functional description

The System Timer Module (STM) is a 32-bit timer designed to support commonly required system and 
application software timing functions. The STM includes a 32-bit up counter and four 32-bit compare 
channels with a separate interrupt source for each channel.

The STM has one 32-bit up counter (STM_CNT) that is used as the time base for all channels. When 
enabled, the counter increments at the system clock frequency divided by a prescale value. The 
STM_CR[CPS] field sets the divider to any value in the range from 1 to 256. The counter is enabled with 
the STM_CR[TEN] bit. When enabled in normal mode the counter continuously increments. When 
enabled in debug mode the counter operation is controlled by the STM_CR[FRZ] bit. When the 
STM_CR[FRZ] bit is set, the counter is stopped in debug mode, otherwise it continues to run in debug 
mode. The counter rolls over at 0xFFFF_FFFF to 0x0000_0000 with no restrictions at this boundary.

The STM has four identical compare channels. Each channel includes a channel control register 
(STM_CCR

n

), a channel interrupt register (STM_CIR

n

) and a channel compare register (STM_CMP

n

). 

The channel is enabled by setting the STM_CCR

n

[CEN] bit. When enabled, the channel will set the 

STM_CIR[CIF] bit and generate an interrupt request when the channel compare register matches the timer 
counter. The interrupt request is cleared by writing a 1 to the STM_CIR

n

[CIF] bit. A write of 0 to the 

STM_CIR

n

[CIF] bit has no effect.

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

ABB AC 800M Library Object Style Manual preview
AC 800M
Brand: ABB Pages: 120
ABB ABILITY SSC600 Product Manual preview
ABILITY SSC600
Brand: ABB Pages: 42
Facility Explorer FX Series Installation Instructions preview
FX Series
Brand: Facility Explorer Pages: 4
Calsense ET2000e Programming Manual preview
ET2000e
Brand: Calsense Pages: 74
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Brand: Yamaha Pages: 92
York CIW01 Installation & Maintenance Manual preview
CIW01
Brand: York Pages: 24
Abov MC80F0304 User Manual preview
MC80F0304
Brand: Abov Pages: 138
Anilam 4200T CNC Manual preview
4200T CNC
Brand: Anilam Pages: 31
EFI E-42 Installation And Service Manual preview
E-42
Brand: EFI Pages: 127
maxxess eMAX-EP4502 Installation Manual preview
eMAX-EP4502
Brand: maxxess Pages: 11
SOLARJACK PVA 5-30 User Manual preview
PVA 5-30
Brand: SOLARJACK Pages: 14
IFM EC2121 System Manual preview
EC2121
Brand: IFM Pages: 41
Mita WP3000 Manual preview
WP3000
Brand: Mita Pages: 7
M-Audio Keystation 61es User Manual preview
Keystation 61es
Brand: M-Audio Pages: 15
Jordan Valve Mark 60 Series Installation & Maintenance Instructions preview
Mark 60 Series
Brand: Jordan Valve Pages: 5
Ulvac UK-2 Instruction Manual preview
UK-2
Brand: Ulvac Pages: 48
Mono DELTA DEPOSITOR Operation Manual preview
DELTA DEPOSITOR
Brand: Mono Pages: 60
Trio MC508 P848 Quick Start Manual preview
MC508 P848
Brand: Trio Pages: 8

Brands by name

Popular brands

Load more brands