manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 25 FlexPWM

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

657

 

25.6.2

Register descriptions

The address of a register is the sum of a base address and an address offset. The base address is defined at 
the core level and the address offset is defined at the module level. There are a set of registers for each 
PWM submodule, for the configuration logic, and for each Fault channel.

25.6.3

Submodule registers

These registers are repeated for each PWM submodule. 

25.6.3.1

Counter Register (CNT)

This read-only register displays the state of the signed 16-bit submodule counter. This register is not byte 
accessible.

25.6.3.2

Initial Count Register (INIT)

The 16-bit signed value in this register defines the initial count value for the PWM in PWM clock periods. 
This is the value loaded into the submodule counter when local sync, master sync, or master reload is 
asserted (based on the value of INIT_SEL) or when FORCE is asserted and force init is enabled. For PWM 
operation, the buffered contents of this register are loaded into the counter at the start of every PWM cycle. 
This register is not byte accessible.

Address: Base + 0x0000 (Submodule 0)

Base + 0x0050 (Submodule 1)
Base + 0x00A0 (Submodule 2)
Base + 0x00F0 (Submodule 3)

Access: User read-only

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

CNT

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 25-3. Counter Register (CNT)

Address: Base + 0x0002 (Submodule 0)

Base + 0x0052 (Submodule 1)
Base + 0x00A2 (Submodule 2)
Base + 0x00F2 (Submodule 3)

Access: User read/write

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

INIT

W

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 25-4. Initial Count Register (INIT)

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Campbell CR10 PROM Replacement Procedure preview
CR10 PROM
Brand: Campbell Pages: 8
Easy Heat RS2 Installation And Operation Instructions preview
RS2
Brand: Easy Heat Pages: 4
S&C 6802 Application Manual preview
6802
Brand: S&C Pages: 8
Ultraflex B47 Installation Instructions Manual preview
B47
Brand: Ultraflex Pages: 7
Identiv Freedom Bridge FB3 Installation Manual preview
Freedom Bridge FB3
Brand: Identiv Pages: 2
AirCycler SmartExhaust Manual preview
SmartExhaust
Brand: AirCycler Pages: 2
TS Performance Torque Converter Lock-Up Manual preview
Torque Converter Lock-Up
Brand: TS Performance Pages: 4
Swagelok BSH 10 Series User Manual preview
BSH 10 Series
Brand: Swagelok Pages: 20
Zeversolar Zeverlution S Setup Manual preview
Zeverlution S
Brand: Zeversolar Pages: 8
ECUE DMX2CC 12ch Setup Manual preview
DMX2CC 12ch
Brand: ECUE Pages: 39
Regada SP 1 Installation, Service And Maintenance Instructions preview
SP 1
Brand: Regada Pages: 41
Glitch'd Gaming GG AIO Quick Start Manual preview
GG AIO
Brand: Glitch'd Gaming Pages: 12
FAAC AT- 4/868 UHF Installation Manual preview
AT- 4/868 UHF
Brand: FAAC Pages: 25
Digi XBee 865 Getting Started Manual preview
XBee 865
Brand: Digi Pages: 19
RADIKAL TECHNOLOGIES SAC-2K Manual preview
SAC-2K
Brand: RADIKAL TECHNOLOGIES Pages: 36
Evoqua WALLACE & TIERNAN MULTI-FUNCTIONS-CONTROLLER Short Operating Instructions preview
WALLACE & TIERNAN MULTI-FUNCTIONS-CONTROLLER
Brand: Evoqua Pages: 4
Danfoss AMD 610 AS Installation Manual preview
AMD 610 AS
Brand: Danfoss Pages: 2
AudioCodes Mediant 4000B Quick Setup Manual preview
Mediant 4000B
Brand: AudioCodes Pages: 10

Brands by name

Popular brands

Load more brands