manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

Share
Download
NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 45

Chapter 1 Introduction

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

45

 

buffers. Prefetch buffer hits allow no-wait responses. Normal flash memory array accesses are registered 
and are forwarded to the system bus on the following cycle, incurring two wait-states.

The flash memory module provides the following features:

•

As much as 320 KB flash memory
— 6 blocks (32 KB + 2×16 KB + 32 KB + 32 KB + 128 KB) code flash memory
— 4 blocks (16 KB + 16 KB + 16 KB + 16 KB) data flash memory
— Full Read-While-Write (RWW) capability between code flash memory and data flash memory

•

Four 128-bit wide prefetch buffers to provide single cycle in-line accesses (prefetch buffers can be 
configured to prefetch code or data or both)

•

Typical flash memory access time: no wait-state for buffer hits, 2 wait-states for page buffer miss 
at 64 MHz

•

Hardware managed flash memory writes handled by 32-bit RISC Krypton engine

•

Hardware and software configurable read and write access protections on a per-master basis

•

Configurable access timing allowing use in a wide range of system frequencies

•

Multiple-mapping support and mapping-based block access timing (up to 31 additional cycles) 
allowing use for emulation of other memory types

•

Software programmable block program/erase restriction control

•

Erase of selected block(s)

•

Read page sizes
— Code flash memory: 128 bits (4 words)
— Data flash memory: 32 bits (1 word)

•

ECC with single-bit correction, double-bit detection for data integrity
— Code flash memory: 64-bit ECC
— Data flash memory: 32-bit ECC

•

Embedded hardware program and erase algorithm 

•

Erase suspend and program abort

•

Censorship protection scheme to prevent flash memory content visibility

•

Hardware support for EEPROM emulation

1.6.5

Static random access memory (SRAM)

The MPC5602P SRAM module provides up to 20 KB of general-purpose memory.

ECC handling is done on a 32-bit boundary and is completely software compatible with MPC55xx family 
devices containing an e200z6 core and 64-bit wide ECC.

The SRAM module provides the following features:

•

Supports read/write accesses mapped to the SRAM from any master

•

Up to 20 KB general purpose SRAM

•

Supports byte (8-bit), half word (16-bit), and word (32-bit) writes for optimal use of memory

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands