manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 20 Deserial Serial Peripheral Interface (DSPI)

MPC5602P Microcontroller Reference Manual, Rev. 4

444

Freescale Semiconductor

 

Table 20-3. DSPI

x

_MCR field descriptions

Field

Description

0

MSTR

Master/slave mode select
Configures the DSPI for master mode or slave mode.
0 DSPI is in slave mode. 
1 DSPI is in master mode. 

1

CONT_SCKE

Continuous SCK enable
Enables the serial communication clock (SCK) to run continuously. Refer to 

Section 20.8.6, 

“Continuous Serial communications clock

 for details.

0 Continuous SCK disabled 
1 Continuous SCK enabled 

Note:

If the FIFO is enabled with continuous SCK mode, before setting the CONT_SCKE bit, the 
TX-FIFO should be cleared and only CTAR0 register should be used for transfer attributes 
otherwise a change in SCK frequency occurs.

2–3

DCONF

[0:1]

DSPI configuration
The following table lists the DCONF values for the various configurations.

4

FRZ

Freeze
Enables the DSPI transfers to be stopped on the next frame boundary when the device enters debug 
mode.
0 Do not halt serial transfers. 
1 Halt serial transfers. 

5

MTFE

Modified timing format enable
Enables a modified transfer format to be used. Refer to 

Section 20.8.5.4, “Modified SPI transfer 

format (MTFE = 1, CPHA = 1)

 for more information.

0 Modified SPI transfer format disabled 
1 Modified SPI transfer format enabled 

6

PCSSE

Peripheral chip select strobe enable
Enables the CS5_

x

 to operate as a CS strobe output signal. 

Refer to 

Section 20.8.4.5, “Peripheral Chip Select strobe enable (CS5_x)

 for more information.

0 CS5_

x

 is used as the Peripheral chip select 5 signal. 

1 CS5_

x

 is used as an active-low CS strobe signal. 

7

ROOE

Receive FIFO overflow overwrite enable
Enables an RX FIFO overflow condition to ignore the incoming serial data or to overwrite existing 
data. If the RX FIFO is full and new data is received, the data from the transfer that generated the 
overflow is ignored or put in the shift register. 
If the ROOE bit is set, the incoming data is put in the shift register. If the ROOE bit is cleared, the 
incoming data is ignored. Refer to 

Section 20.8.7.6, “Receive FIFO overflow interrupt request 

(RFOF)

 for more information.

0 Incoming data is ignored. 
1 Incoming data is put in the shift register. 

8–9

Reserved, but implemented. These bits are writable, but have no effect. 

DCONF

Configuration

00

SPI

01

Invalid value

10

Invalid value

11

Invalid value

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Barco Argus Information preview
Argus
Brand: Barco Pages: 6
Hanna Instruments BL120 Instruction Manual preview
BL120
Brand: Hanna Instruments Pages: 54
Hanna Instruments BL 983320-0 Instruction Manual preview
BL 983320-0
Brand: Hanna Instruments Pages: 2
U-Prox IP500 Installation And Programming Manual preview
IP500
Brand: U-Prox Pages: 25
Allen-Bradley PowerFlex 755 IP00 Installation Instructions Manual preview
PowerFlex 755 IP00
Brand: Allen-Bradley Pages: 78
Elby Designs ASM301-ADSR Diagrams preview
ASM301-ADSR
Brand: Elby Designs Pages: 4
TEL AFA4000/1/AS Installation And Calibration Manual preview
AFA4000/1/AS
Brand: TEL Pages: 26
Vimar EAM6 Installation And Operation Manual preview
EAM6
Brand: Vimar Pages: 32
Elotech R 1300 Description And Operating Manual preview
R 1300
Brand: Elotech Pages: 20
Intermatic NE 1 Operating Instructions preview
NE 1
Brand: Intermatic Pages: 2
NCE CAB-04p Operation Manual preview
CAB-04p
Brand: NCE Pages: 4
Zennio MAXinBOX 24 ZIO-MB24 User Manual preview
MAXinBOX 24 ZIO-MB24
Brand: Zennio Pages: 24
YASKAWA Sigma II Series User Manual preview
Sigma II Series
Brand: YASKAWA Pages: 359
Technologic TLK 43 Operating Instructions Manual preview
TLK 43
Brand: Technologic Pages: 21
Eaton AutoVAR 600 Instructions For Replacing preview
AutoVAR 600
Brand: Eaton Pages: 2
Optelec Alva BC640 User Manual preview
Alva BC640
Brand: Optelec Pages: 41
ST FP-SNS-SMARTAG1 Quick Start Manual preview
FP-SNS-SMARTAG1
Brand: ST Pages: 25
Samson Trovis 6493 Mounting And Operating Instructions preview
Trovis 6493
Brand: Samson Pages: 128

Brands by name

Popular brands

Load more brands