NXP Semiconductors SAFE ASSURE Qorivva MPC5601P Reference Manual Download Page 44 | Manualshive

Page: 44 / 954

background image

Chapter 1 Introduction

MPC5602P Microcontroller Reference Manual, Rev. 4

44

Freescale Semiconductor

The crossbar provides the following features:

•

3 master ports:
— e200z0 core complex instruction port
— e200z0 core complex Load/Store Data port
— eDMA

•

3 slave ports:
— Flash memory (Code and Data)
— SRAM
— Peripheral bridge

•

32-bit internal address, 32-bit internal data paths

•

Fixed Priority Arbitration based on Port Master

•

Temporary dynamic priority elevation of masters

1.6.3

Enhanced direct memory access (eDMA)

The enhanced direct memory access (eDMA) controller is a second-generation module capable of
performing complex data movements via 16 programmable channels, with minimal intervention from the
host processor. The hardware micro architecture includes a DMA engine which performs source and
destination address calculations, and the actual data movement operations, along with an SRAM-based
memory containing the transfer control descriptors (TCD) for the channels.

The eDMA module provides the following features:

•

16 channels support independent 8-, 16- or 32-bit single value or block transfers

•

Supports variable-sized queues and circular queues

•

Source and destination address registers are independently configured to either post-increment or
to remain constant

•

Each transfer is initiated by a peripheral, CPU, or eDMA channel request

•

Each eDMA channel can optionally send an interrupt request to the CPU on completion of a single
value or block transfer

•

DMA transfers possible between system memories, DSPIs, ADC, FlexPWM, eTimer and CTU

•

Programmable DMA channel multiplexer allows assignment of any DMA source to any available
DMA channel with as many as 30 request sources

•

eDMA abort operation through software

1.6.4

Flash memory

The MPC5602P provides 320 KB of programmable, non-volatile, flash memory. The non-volatile
memory (NVM) can be used for instruction and/or data storage. The flash memory module is interfaced
to the system bus by a dedicated flash memory controller. It supports a 32-bit data bus width at the system
bus port, and a 128-bit read data interface to flash memory. The module contains four 128-bit wide prefetch

«
...
42
43
44
45
46
...
»

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Brand: Fairchild Pages: 2

Brand: Kamstrup Pages: 36

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

xPico 200 Series

Brand: Lantronix Pages: 7

Brand: Lantronix Pages: 3

Brand: Lantronix Pages: 15

Brand: Namron Pages: 3

Brand: OMC Pages: 18

Brand: L-Acoustics Pages: 20

Brand: ZKTeco Pages: 2

Brand: Lampert Pages: 15

Touch Screen Controller RX142

Brand: 3M Pages: 29

Brand: Dahua Technology Pages: 75

Brand: National Instruments Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands