manualshive.com logo in svg

NXP Semiconductors SAFE ASSURE Qorivva MPC5601P, Reference Manual

The NXP Semiconductors SAFE ASSURE Qorivva MPC5601P is a cutting-edge automotive microcontroller, offering unparalleled security features. Gain a comprehensive understanding of its functionalities by accessing the free Reference Manual. Download it now from manualshive.com, the ultimate destination for user manuals. Explore this game-changing product manual and unlock its full potential.

Share
Download
background image

Chapter 18 Enhanced Direct Memory Access (eDMA)

MPC5602P Microcontroller Reference Manual, Rev. 4

Freescale Semiconductor

395

 

18.5.2.10 eDMA Clear Error Register (EDMA_CERR)

The EDMA_CERR provides a simple memory-mapped mechanism to clear a given bit in the EDMA_ERL 
to disable the error condition flag for a given channel. The given value on a register write causes the 
corresponding bit in the EDMA_ERL to be cleared. Setting bit 1 (CER

n

) provides a global clear function, 

forcing the entire contents of the EDMA_ERL to be zeroed, clearing all channel error indicators. Reads of 
this register return all zeroes.

18.5.2.11 eDMA Set START Bit Register (EDMA_SSBR)

The EDMA_SSBR provides a simple memory-mapped mechanism to set the START bit in the TCD of the 
given channel. The data value on a register write causes the START bit in the corresponding transfer 
control descriptor to be set. Setting bit 1 (SSB

n

) provides a global set function, forcing all START bits to 

be set. Reads of this register return all zeroes.

Address: Base + 0x001D

Access: User write-only

0

1

2

3

4

5

6

7

R

0

0

0

0

0

0

0

0

W

CERR[0:6]

Reset

0

0

0

0

0

0

0

0

Figure 18-11. eDMA Clear Error Register (EDMA_CERR)

Table 18-11. EDMA_CERR field descriptions

Field

Description

0

Reserved.

1–7

CER[0:6]

Clear error indicator.
0–15 Clear corresponding bit in EDMA_ERL
16–63 Reserved
64–127 Clear all bits in EDMA_ERL

Address: Base + 0x001E

Access: User write-only

0

1

2

3

4

5

6

7

R

0

0

0

0

0

0

0

0

W

SSB[0:6]

Reset

0

0

0

0

0

0

0

0

Figure 18-12. eDMA Set START Bit Register (EDMA_SSBR)

Table 18-12. EDMA_SSBR field descriptions

Field

Description

0

Reserved.

1–7

SSB[0:6]

Set START bit (channel service request).
0–15 Set the corresponding channel’s TCD START bit
16–63 Reserved
64–127 Set all TCD START bits

Note:

Bit 2 (SSB1) is not used.

Summary of Contents for SAFE ASSURE Qorivva MPC5601P



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SAFE ASSURE Qorivva MPC5601P

Waterway OASIS Instruction Manual preview
OASIS
Brand: Waterway Pages: 16
Lamtec FA1 Quick Reference preview
FA1
Brand: Lamtec Pages: 22
ABB RHD8000 Series Instructions Manual preview
RHD8000 Series
Brand: ABB Pages: 17
Watts KONTACT Manual preview
KONTACT
Brand: Watts Pages: 17
Epsolar eTracer ET4415BND Operation Manual preview
eTracer ET4415BND
Brand: Epsolar Pages: 44
Infineon XE166 Series Hardware Manual preview
XE166 Series
Brand: Infineon Pages: 28
G-Tech FIELD MATE User Manual And Installation Manual preview
FIELD MATE
Brand: G-Tech Pages: 26
Kelly KLS7250H User Manual preview
KLS7250H
Brand: Kelly Pages: 35
maxon motor EPOS2 24/5 Hardware Reference Manual preview
EPOS2 24/5
Brand: maxon motor Pages: 44
Velleman-Kit EDU01 Manual preview
EDU01
Brand: Velleman-Kit Pages: 32
SystemAir fantech IPF05-1L Installation Instructions preview
fantech IPF05-1L
Brand: SystemAir Pages: 2
DROPSA VIP5 Quick Start Manual preview
VIP5
Brand: DROPSA Pages: 29
Samson TROVIS 6495 Series Mounting And Operating Instructions preview
TROVIS 6495 Series
Brand: Samson Pages: 156
GIA Giatsu GIA-J105 Owner'S Manual preview
Giatsu GIA-J105
Brand: GIA Pages: 9
Digital Acoustics IP7-MZC-FD Application Manual preview
IP7-MZC-FD
Brand: Digital Acoustics Pages: 7
Brooks 5851EM Series Installation And Operation Manual preview
5851EM Series
Brand: Brooks Pages: 62
LMF Manufacturing HPH User Manual preview
HPH
Brand: LMF Manufacturing Pages: 51
Fego Precision Industrial TP48 Instructions preview
TP48
Brand: Fego Precision Industrial Pages: 2

Brands by name

Popular brands

Load more brands