manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

Share
Download
NXP Semiconductors MSC8113 Reference Manual Download Page 91

Direct Slave Interface, System Bus, Ethernet, and Interrupt Signals

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

3-15

TA

Input/ 

Output

Transfer Acknowledge
Indicates that a data beat is valid on the data bus. For single-beat transfers, TA assertion 
indicates the termination of the transfer. For burst transfers, TA is asserted eight times to 
indicate the transfer of eight data beats, with the last assertion indicating the termination of 
the burst transfer.

TEA

Input/ 

Output

Transfer Error Acknowledge
Assertion indicates a failure of the data tenure transaction.The masters within the MSC8113 
monitor the state of this pin. The MSC8113 internal bus monitor can assert this pin if it 
identifies a bus transfer that does not complete.

NMI

Input

Non-Maskable Interrupt 
When an external device asserts this line, it generates an non-maskable interrupt in the 
MSC8113, which is processed internally (default) or is directed to an external host for 
processing (see NMI_OUT).

NMI_OUT

Output

Non-Maskable Interrupt Output
An open-drain pin driven from the MSC8113 internal interrupt controller. Assertion of this 
output indicates that a non-maskable interrupt is pending in the MSC8113 internal interrupt 
controller, waiting to be handled by an external host.

PSDVAL

Input/ 

Output

Port Size Data Valid
Indicates that a data beat is valid on the data bus. The difference between the TA pin and the 
PSDVAL pin is that the TA pin is asserted to indicate data transfer terminations, while the 
PSDVAL signal is asserted with each data beat movement. When TA is asserted, PSDVAL is 
always asserted. However, when PSDVAL is asserted, TA is not necessarily asserted. For 
example, if the DMA initiates a double word (2 

×

 64 bits) transaction to a memory device with 

a 32-bit port size, PSDVAL is asserted three times without TA and, finally, both pins are 
asserted to terminate the transfer.

IRQ7

INT_OUT

Input

Output

Interrupt Request 7
One of fifteen external lines that can request a service routine, via the internal interrupt 
controller, from the SC140.

Interrupt Output
Assertion of this output indicates that an unmasked interrupt is pending in the MSC8113 
internal interrupt controller.

Notes: 1.

See the System Interface Unit (SIU) chapter in the MSC8113 Reference Manual for details on how to configure 
these pins.

2.

When used as the bus control arbiter, the MSC8113 can support up to three external bus masters. Each master 
uses its own set of Bus Request, Bus Grant, and Data Bus Grant signals (BR/BG/DBG, 
EXT_BR2/EXT_BG2/EXT_DBG2, and EXT_BR3/EXT_BG3/EXT_DBG3). Each of these signal sets must be 
configured to indicate whether the external master is or is not a MSC8113 master device. See the Bus 
Configuration Register (BCR) description in the System Interface Unit (SIU) chapter in the MSC8113 Reference 
Manual for details on how to configure these pins. The second and third set of pins is defined by EXT_xxx to 
indicate that they can only be used with external master devices. The first set of pins (BR/BG/DBG) have a dual 
function. When the MSC8113 is not the bus arbiter, it uses these signals (BR/BG/DBG) to obtain master control 
of the bus.

Table 3-5.  DSI, System Bus, Ethernet, and Interrupt Signals (Continued) 

Signal Name

Type

Description

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands