manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

Share
Download
NXP Semiconductors MSC8113 Reference Manual Download Page 597

Instruction Decoding

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

18-7

00011

CLAMP

Optional in the IEEE Std. 1149.1. This public instruction selects the one-bit Bypass Register 
as the serial path between TDI and TDO, while allowing signals driven from the component 
to be determined from the Boundary Scan Register. During testing of ICs on PCBs, it may be 
necessary to place static guarding values on signals that control logic operations not 
involved in the test. The EXTEST instruction could be used for this purpose, but since it 
selects the BSR, the required guarding signals would be loaded as part of the complete 
serial data stream shifted in, both at the start of the test and each time a new test pattern is 
entered. Since the CLAMP instruction allows guarding values to be applied using the BSR of 
the appropriate ICs while selecting their Bypass Registers, it allows much faster testing than 
EXTEST. Data in the boundary scan cell remains unchanged until a new instruction is shifted 
in. 
Note:

The CLAMP instruction also asserts internal reset for the MSC8113 system logic to 
force a predictable internal state while external boundary scan operations are 
performed.

00100

HIGHZ

Optional in the IEEE Std. 1149.1. It is a manufacturer’s public instruction to prevent 
back-drive of the outputs during circuit-board testing. When HIGHZ is invoked, all output 
drivers, including the two-state drivers, are turned off (that is, high impedance). The HIGHZ 
instruction selects the Bypass Register. It also asserts internal reset for the MSC8113 
system logic to force a predictable internal state while external boundary scan operations are 
performed.

00101

—

Reserved

00110

ENABLE_EONCE

Not included in the IEEE Std. 1149.1. This public instruction allows you to perform system 
debug functions. When the ENABLE_EONCE instruction is decoded, TDI and TDO connect 
directly to the EOnCE registers. The EOnCE controller selects the specific EOnCE register 
connected between TDI and TDO, depending on the EOnCE instruction being executed. All 
communication with the EOnCE controller is through the 

SELECT

-

DR

-

SCAN

 path of the JTAG 

TAP Controller. Before the ENABLE_EONCE instruction is selected, the CHOOSE_EONCE 
instruction should be executed to define which EOnCE is to be activated.
Note:

This instruction is valid only if the core processor is running.

00111

DEBUG_REQUEST

Not included in the IEEE Std. 1149.1. This public instruction allows you to generate a debug 
request signal to the MSC8113. When the DEBUG_REQUEST instruction is decoded, TDI 
and TDO connect to the EOnCE registers. In addition, ENABLE_EONCE is active and forced 
to request Debug mode from the MSC8113, in order to perform system debug functions. 
Before the DEBUG_REQUEST instruction is selected, the CHOOSE_EONCE instruction 
should be executed to define which EOnCE is to be selected for DEBUG_REQUEST. 
Note:

Issuing this instruction does not ensure that the SC140 core enters the debug state. 
Monitor the core status to make sure that it has stopped.

01000

PRIVATE

Manufacturer’s private instruction.
Note:

Selecting this instruction many cause unpredictable operation of the device.

01001

CHOOSE_EONCE

Not included in the IEEE Std. 1149.1. This instruction enables selected SC140 EOnCE 
modules. All instructions executed after this one target only the selected EOnCE set. 
Therefore, this instruction always executes, regardless of the selected EOnCE set. 

01010

—

Reserved

01011

—

Reserved

01100

PRIVATE

Manufacturer’s private instruction.
Note:

Selecting this instruction many cause unpredictable operation of the device.

01101

LOAD_GPR

Not included in the IEEE Std. 1149.1: LOAD GPR

When programming the GPR, use only the bits permitted in Table 18-6.

01110

PRIVATE

Manufacturer’s private instruction.
Note:

Selecting this instruction many cause unpredictable operation of the device.

01111

—

Reserved

Table 18-3.  Instruction Decoding (Continued)

Bits 4-0

Instruction

Description

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands