manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

Share
Download
NXP Semiconductors MSC8113 Reference Manual Download Page 311

Basic Architecture

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

12-3

12.1 Basic Architecture

Each external bank can be assigned to any one of the memory controller machines (except UPMC 
and local bus GPCM) via BRx[MS] as shown in Figure 12-2 (bank 0 and bank 2 are located on 
the external system bus). The BRx[MS] and MxMR[BSEL] bits (for UPMs) assign banks to the 
system bus or local bus as shown in Figure 12-2. Addresses are decoded by comparing BRx[BA] 
with a bit-wise AND of 

A[0–16]

 and ORx[AM]. If an address match occurs in multiple banks, the 

lowest numbered bank has priority. However, if a system bus access hits a bank allocated to the 
local bus, the access is transferred to the local bus. Local bus access hits to banks assigned to the 
system bus are ignored. When a memory address matches BRx[BA], the corresponding machine 
takes ownership of the external signals that control access and maintains control until the cycle 
ends. See Section 12.8, Memory Controller Programming Model, on page 12-95 for details on 
the BRx, ORx, and MxMR registers.

The following features are common to all machines:

„

There is a 17-bit most-significant address decode on each memory bank.

„

The block size of each memory bank varies between 32 KB (1 MB for SDRAM) and 4 GB 
(128 MB for SDRAM using bank-based interleaving). 

„

Normal parity can be generated and checked for any external memory bank.

„

Read-modify-write parity can be generated and checked for any external memory bank 
with a 32-bit or 64-bit port size. Using RMW parity on a bank with a 32-bit port size 
requires the bus to be in strict 60x mode (BCR[ETM] = 0). See the discussion of the Bus 
Configuration Register (BCR) in Section 4.2, SIU Programming Model.

„

Error checking and correction (ECC) can be generated for any external memory bank with 
a 64-bit port size.

„

Each external memory bank can be selected for read-only or read/write operation. 

„

Each external memory bank can use data pipelining, which reduces the required data 
set-up time for synchronous devices.

„

Each external memory bank can be controlled by an external memory controller or bus 
slave.

The memory controllers functionality minimizes the need for glue logic in MSC8113-based 
systems. In Figure 12-3, 

CS0

 is used with the 16-bit boot EPROM with BR0[MS] defaulting to 

select the GPCM. 

CS1

 is used as the 

RAS

 signal for 32-bit DRAM with BR1[MS] configured to 

select UPMA. 

PBS[0–3] 

are used as 

CAS

 signals on the DRAM. In the example, the boot EPROM 

and DRAM connect to the external system bus.

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands