manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual

Share
Download
NXP Semiconductors MSC8113 Reference Manual Download Page 170

MSC8113 Reference Manual, Rev. 0

7-2

Freescale Semiconductor

Clocks

„

The Ethernet interface has two clock zones:
— The serial interface:

•

MII mode. The receiver clock is 

ETHRX_CLK

; the transmitter clock is 

ETHTX_CLK

.

•

RMII mode. The receiver and transmitter are clocked by 

ETHREF_CLK

.

•

SMII mode. The receiver and transmitter are clocked by 

ETHCLOCK

.

— Local bus interface is clocked by the BUSES_CLOCK.

7.1 Clock Generation

The 

CLKOUT

 signal, the internal CORE_CLOCK, and the BUSES_CLOCK are generated as a 

function of the 

CLKIN

 signal, guaranteeing minimum skew between the 

CLKOUT

 and 

BUSES_CLOCK of all the MSC8113 devices. Figure 7-1 shows the MSC8113 clock scheme.

 

CLKIN

 is generated by an external oscillator and is fed to the SPLL that divides and multiplies its 

frequency according to the PLLRDF, PLLFDF, PLLODF, and the BUSDF factors as configured 
by the System Clock Mode Status Register 

(

SCMSR) (see Section 7.4, Clocks Programming 

Model). The PLLPDF field divides the frequency by 1 or 2. The PLL VCO clock is generated by 
multiplying the PLL predivider clock by: 2 

×

 PLLFDF 

×

 PLLODF 

×

 BUSDF. The PLL output 

clock is generated by dividing the PLL VCO clock by: 2 

×

 PLLODF. The SCMSR[BUSDF] bit 

value controls the frequency ratio between the BUSES_CLOCK and the CORES_CLOCK. The 

CLKOUT

 is typically the system bus clock or the local bus clock.

In Figure 7-2, the CORES_CLOCK and BUSES_CLOCK frequency ratio is 1:3.

Figure 7-1.  CORES_CLOCK, BUSES_CLOCK, and CLKCOUT Generation

Figure 7-2.  CORES_CLOCK, BUSES_CLOCK, and CLKOUT Example

BUSES_CLOCK

CLKOUT

PLLRDF: PLL input clock division factor

PLLFDF: PLL Feadback division factor

PLLODF: PLL output clock division factor

BUSDF: CLOCK_BUSES division factor

CORES_CLOCK

CLKIN

SPLL

Division by

PLLRDF

Division by

2 

×

 PLLODF

Division

BUSDF

by

Division by

PLLFDF

PFD and 

Division

BUSDF

by

VCO

CORES_CLOCK

BUSES_CLOCK

CLKOUT

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands