manualshive.com logo in svg

NXP Semiconductors MSC8113, Reference Manual, Page: 107 / 1202

Share
Download
NXP Semiconductors MSC8113 Reference Manual Download Page 107

Architecture

MSC8113 Reference Manual, Rev. 0

Freescale Semiconductor

4-3

Many aspects of system configuration are controlled by several SIU module configuration 
registers described in Section 4.2.1, System Configuration and Protection Registers.

4.1.1   Bus Monitors

There are two bus monitors, one for the system bus and one for the local bus. The bus monitor 
ensures that each bus cycle terminates within a reasonable period. The bus monitor does not 
count when the bus is idle. When a transaction starts (

TS

 asserted), the bus monitor starts 

counting down from the time-out value.

For standard bus transactions with an address tenure and a data tenure, the bus monitor counts 
until a data beat is acknowledged on the bus. It then reloads the time-out value and resumes the 
count down. This process continues until the whole data tenure is completed. Following the data 
tenure, the bus monitor idles if there is no pending transaction; otherwise, it reloads the time-out 
value and resumes counting. For address-only transactions, the bus monitor counts until 

AACK

 is 

asserted.

If the monitor times out for a standard bus transaction, transfer error acknowledge (

TEA

) is 

asserted. If the monitor times out for an address-only transaction, the bus monitor asserts 

AACK

 

and a core machine check interrupt or reset is generated, depending on SYPCR[SWRI]. Note that 
the device does not generate address-only transactions.

To allow variation in system peripheral response times, SYPCR[BMT] defines the time-out 
period, whose maximum value can be 2,040 system bus clocks. The timing mechanism is clocked 
by the system bus clock divided by eight.

Figure 4-2.  System Configuration and Protection Logic

Module

Configuration

Bus

Monitors

Periodic Interrupt

Timer

Software

Watchdog Timer

Time

Counter

Interrupt

Interrupt

System Reset

TIMERSCLK

Bus Clock

TIMERSCLK

System Reset

Bus clock/8

TEA

NMI to Cores

Summary of Contents for MSC8113



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments