manualshive.com logo in svg

NXP Semiconductors MPT612, User Manual, Page: 57 / 269

Share
Download
NXP Semiconductors MPT612 User Manual Download Page 57

UM10413

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2011. All rights reserved.

User manual

Rev. 1 — 16 December 2011 

57 of 268

NXP Semiconductors

UM10413

MPT612 User manual

To summarize: on the MPT612, the wake-up timer enforces a minimum reset duration 
based on the crystal oscillator, and is activated whenever there is a wake-up from 
Power-down mode or any type of reset.

10.13 Code 

security vs. debugging

Applications in development typically need the debugging and tracing facilities in the 
MPT612. Later in the life cycle of an application, it can be more important to protect the 
application code from observation by hostile or competitive eyes. The Code Read 
Protection feature on the MPT612 allows an application to control whether it can be 
debugged or protected from observation.

Details on the way Code Read Protection works can be found in 

Section 25.8 “Code Read 

Protection (CRP)” on page 223

.

11. Pin configuration

11.1 Pinout

 

Fig 16. LQFP48 pin configuration

MPT612FBD48

PIO19/MAT1_2/MISO1

PIO11/CTS1/CAP1_1/AD4

PIO20/MAT1_3/MOSI1

PIO10/RTS1/CAP1_0/AD3

PIO21/SSEL1/MAT3_0

PVCURRENTSENSE

V

DD(RTC)

PVVOLTSENSEBOOST

V

DDC

PVVOLTSENSEBUCK

RST

GNDADC

GND

PIO9/RXD1/PWMOUT2

PIO27/TRST

PIO8/TXD1/PWMOUT1

PIO28/TMS

PWMOUT0

PIO29/TCK

JTAGSEL

XTAL1

RTCK

XTAL2

RTCX2

PIO18/CAP1_3/SDA1

PIO17/CAP1_2/SCL1

PIO16/EINT0

PIO15/RI1/EINT2

PIO14/DCD1/SCK1/EINT1

GND

V

DD(ADC)

PIO13/DTR1/MAT1_1

V

DD(IO)

PIO26/AD7

PIO25/AD6

PIO12/DSR1/MAT1_0/AD5

PIO0/TXD0/MAT3_1

PIO1/RXD0/MAT3_2

PIO30/TDI/MAT3_3

PIO31/TDO

V

DD(IO)

PIO2/SCL0

GND

RTCX1

PIO3/SDA0

PIO4/SCK0

PIO5/MISO0

PIO6/MOSI0

001aam091

1

2

3

4

5

6

7

8

9

10

11

12

36

35

34

33

32

31

30

29

28

27

26

25

13

14

15

16

17

18

19

20

21

22

23

48

47

46

45

44

43

42

41

40

39

38

37

24

Summary of Contents for MPT612














































































































































































































































































Reviews:

No comments