manualshive.com logo in svg

NXP Semiconductors MPC5644A, Reference Manual, Page: 1237 / 1735

Share
Download
NXP Semiconductors MPC5644A Reference Manual Download Page 1237

Cyclic Redundancy Checker (CRC) Unit

MPC5644A Microcontroller Reference Manual, Rev. 6

Freescale Semiconductor

1237

 

Chapter 29  
Cyclic Redundancy Checker (CRC) Unit

29.1

Overview

The CRC module provides a fast on-chip capability for verifying code and data integrity. This capability 
is particularly important in safety applications. Examples include:

•

Verifying memory integrity by setting it to a known value, calculating a checksum and comparing 
the calculated checksum against a stored checksum value

•

Verifying code integrity by comparing its calculated checksum to its stored checksum value

•

Verifying the integrity of data received from a network by comparing its received checksum to its 
calculated checksum

CRC functionality can be implemented in software but there are significant speed advantages to be gained 
by offloading CRC computation tasks from the processor core to the CRC module. Further gains are made 
when data is written to the CRC module via DMA.

NOTE

This chapter does not discuss the details of computing CRC checksums but 
there are many articles to be found via internet searches. One that might be 
of particular interest is “A Painless Guide to CRC Error Detection 
Algorithms” by Ross Williams.

29.2

Features

The CRC module on the MPC5644A includes the following features:

•

3 “contexts”—A context is a CRC engine with its own independent set of configuration and data 
registers. The MPC5644A CRC module can process up to three separate data streams concurrently.

•

Each context supports CRC-16-CCITT and CRC-32 ethernet polynomials

•

Bit-swap and bit-inversion operations can be applied on the final CRC signature

•

Support for byte/half-word/word width of the input data stream

•

Computation is performed with zero wait states

29.2.1

Access and performance

All CRC registers are accessible (read/write) in each access mode: user, supervisor or test. 

The following bus operations (contiguous byte enables) are supported:

•

32-bit data read/write operations to any register

•

Low and high half-word read/write operations to any register

1

•

Byte data write/read operations to any register

2

1. 16-bit operations must be aligned to 16-bit boundaries, i.e., bits 0–15 or bits 16–31. Any unaligned operation results in a bus 
error.

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments