manualshive.com logo in svg

NXP Semiconductors MPC5644A, Reference Manual, Page: 1092 / 1735

Share
Download
NXP Semiconductors MPC5644A Reference Manual Download Page 1092

Enhanced Queued Analog-to-Digital Converter (EQADC)

MPC5644A Microcontroller Reference Manual, Rev. 6

1092

Freescale Semiconductor

 

Figure 25-60. CFIFO Diagram

The detailed behavior of the Push Next Data Pointer and Transfer Next Data Pointer is described in the 
example shown in 

Figure 25-61

 where a CFIFO with 16 entries is shown for clarity of explanation, the 

actual hardware implementation has only four entries. In this example, CFIFOx with 16 entries is shown 
in sequence after pushing and transferring entries.

32-bit Entry 1

32-bit Entry 2

--------------------

--------------------

Push Next

Data Pointer *

Transfer Next

Data Pointer *

CFIFO

Push Register

CFIFO

Control Logic

DMA Done

Interrupt/DMA Request

Control
Signals

Data to
external
device or
to on-chip 
ADCs

Transfer Counter

* All CFIFO entries are memory mapped and the 
entries addressed by these pointers can have their 
absolute addresses calculated using TNXTPTR 
and CFCTR.

Write to  slave-bus 
interface by CPU or 
DMA

Summary of Contents for MPC5644A








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments