manualshive.com logo in svg

NXP Semiconductors MPC5605BK, Reference Manual

Share
Download
NXP Semiconductors MPC5605BK Reference Manual Download Page 730

Chapter 28 Analog-to-Digital Converter (ADC)

MPC5606BK Microcontroller Reference Manual, Rev. 2

728

Freescale Semiconductor

 

28.3.7

DMA functionality

A DMA request can be programmed after the conversion of every channel by setting the respective 
masking bit in the DMAR registers. The DMAR masking registers must be programmed before starting 
any conversion. There is one DMAR per channel type and each ADC module has one DMA request 
associated with it.

The DMA transfers can be enabled using the DMAEN bit of DMAE register. When the DCLR bit of 
DMAE register is set then the DMA request is cleared on the reading of the register for which DMA 
transfer has been enabled.

28.3.8

Interrupts

The ADC generates the following two maskable interrupt signals:

•

ADC_EOC interrupt requests

— EOC (end of conversion)

— ECH (end of chain)

— JEOC (end of injected conversion)

— JECH (end of injected chain)

— EOCTU (end of CTU conversion)

•

WDG

x

L and WDG

x

H (watchdog threshold) interrupt requests

Interrupts are generated during the conversion process to signal events such as End Of Conversion as 
explained in register description for CEOCFR[0..2]. Two registers named CEOCFR[0..2] (Channel 
Pending Registers) and IMR (Interrupt Mask Register) are provided in order to check and enable the 
interrupt request to INT module.

Interrupts can be individually enabled on a channel by channel basis by programming the CIMR (Channel 
Interrupt Mask Register).

Several CEOCFR[0..2] are also provided in order to signal which of the channels’ measurement has been 
completed.

The analog watchdog interrupts are handled by two registers, WTISR (Watchdog Threshold Interrupt 
Status Register) and WTIMR (Watchdog Threshold Interrupt Mask Register), in order to check and enable 
the interrupt request to the INTC module. The Watchdog interrupt source sets two pending bits WDG

x

H 

and WDG

x

L in the WTISR for each of the channels being monitored.

The CEOCFR[0..2] contains the interrupt pending request status. If the user wants to clear a particular 
interrupt event status, then writing a 1 to the corresponding status bit clears the pending interrupt flag (at 
this write operation all the other bits of the CEOCFR[0..2] must be maintained at 0).

28.3.9

External decode signals delay

The ADC provides several external decode signals to select which external channel has to be converted. 
In order to take into account the control switching time of the external analog multiplexer, a Decode 

Summary of Contents for MPC5605BK





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands