manualshive.com logo in svg

NXP Semiconductors MPC5605BK, Reference Manual

Share
Download
NXP Semiconductors MPC5605BK Reference Manual Download Page 553

Chapter 25 FlexCAN

MPC5606BK Microcontroller Reference Manual, Rev. 2

Freescale Semiconductor

551

 

25.3.2

Signal descriptions

25.3.2.1

CAN Rx

This pin is the receive pin from the CAN bus transceiver. Dominant state is represented by logic level 0. 
Recessive state is represented by logic level 1.

25.3.2.2

CAN Tx

This pin is the transmit pin to the CAN bus transceiver. Dominant state is represented by logic level 0. 
Recessive state is represented by logic level 1.

25.4

Memory map/register definition

This section describes the registers and data structures in the FlexCAN module. The base address of the 
module depends on the particular memory map of the MCU. The addresses presented here are relative to 
the base address.

The address space occupied by FlexCAN has 96 bytes for registers starting at the module base address, 
followed by MB storage space in embedded RAM starting at address 0x0060, and an extra ID Mask 
storage space in a separate embedded RAM starting at address 0x0880.

25.4.1

FlexCAN memory mapping

The complete memory map for a FlexCAN module with 64 MBs capability is shown in 

Table 25-2

. 

All registers except for the MCR can be configured to have either supervisor or unrestricted access by 
programming the MCR[SUPV] bit. 

The IFLAG2 and IMASK2 registers are considered reserved space when FlexCAN is configured with 16 
or 32 MBs. The Rx Global Mask (RXGMASK), Rx Buffer 14 Mask (RX14MASK), and the Rx Buffer 15 
Mask (RX15MASK) registers are provided for backwards compatibility and are not used when the BCC 
bit in MCR is asserted.

The address ranges 0x0060–0x047F and 0x0880–0x097F are occupied by two separate embedded 
memories. These two ranges are completely occupied by RAM (1056 and 256 bytes, respectively) only 
when FlexCAN is configured with 64 MBs. When it is configured with 16 MBs, the memory sizes are 288 
and 64 bytes, so the address ranges 0x0180–0x047F and 0x08C0–0x097F are considered reserved space. 
When it is configured with 32 MBs, the memory sizes are 544 and 128 bytes, so the address ranges 
0x0280–0x047F and 0x0900–0x097F are considered reserved space. Furthermore, if the BCC bit in MCR 
is negated, then the whole Rx Individual Mask registers address range (0x0880–0x097F) is considered 
reserved space.

Summary of Contents for MPC5605BK





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands