manualshive.com logo in svg

NXP Semiconductors MPC5566, Reference Manual

Share
Download
NXP Semiconductors MPC5566 Reference Manual Download Page 1061

MPC5566 Microcontroller Reference Manual, Rev. 2

22-24

Freescale Semiconductor

 

22.3.3.11 Interrupt Flags Low Register (CAN

x

_IFRL)

CAN

x

_IFRL defines the flags for 32 message buffer interrupts. It contains one interrupt flag bit per buffer. 

Each successful transmission or reception sets the corresponding IFRL bit. If the corresponding IMRL bit 
is set, an interrupt is generated. Write a 1 to the interrupt flag to clear its value to zero. Writing 0 has no 
effect.

22.4

Functional Description

22.4.1

Overview

The FlexCAN2 module is a CAN protocol engine with a very flexible message buffer configuration 
scheme. The module can have up to 64 message buffers, any of which can be assigned as either a TX buffer 
or an RX buffer. Each message buffer has an assigned interrupt flag to indicate successful completion of 
transmission or reception.

Table 22-15. CAN

x

_IFRH Field Descriptions

Field

Description

0–31

BUF

n

I

Message buffer 

n

 interrupt. Each bit represents the respective FlexCAN2 message buffer (MB63–MB32) 

interrupt. Write 1 to clear.
0 No such occurrence
1 The corresponding buffer has successfully completed transmission or reception.

Address: Base + 0x0030

Access: User R/W1c

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R BUF 

31I

BUF 

30I

BUF 

29I

BUF 

28I

BUF 

27I

BUF 

26I

BUF 

25

BUF 

24I

BUF 

23I

BUF 

22I

BUF 

21I

BUF 

20I

BUF 

19I

BUF 

18I

BUF 

17I

BUF 

16I

W

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R BUF 

15I

BUF 

14I

BUF 

13I

BUF 

12I

BUF 

11I

BUF 

10I

BUF 

09I

BUF 

08I

BUF 

07I

BUF 

06I

BUF 

05I

BUF 

04I

BUF 

03I

BUF 

02I

BUF 

01I

BUF 

00I

W

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

w1c

Reset

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

0

Figure 22-13. Interrupt Flags Low Register (CAN

x

_IFRL)

Table 22-16. CAN

x

_IFRL Field Descriptions

Field

Description

0–31

BUF

n

I

Message buffer 

n

 interrupt. Each bit represents the respective FlexCAN2 message buffer (MB31 to MB0) 

interrupt. Write 1 to clear.
0 No such occurrence
1 The corresponding buffer has successfully completed transmission or reception.

Summary of Contents for MPC5566





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands