manualshive.com logo in svg

NXP Semiconductors MPC555, User Manual

The NXP Semiconductors MPC555 is a cutting-edge microcontroller designed for versatile applications. Enhance your product development experience with our comprehensive User Manual, available for free download at manualshive.com. Discover detailed instructions and unleash the full potential of the MPC555 to transform your projects.

Share
Download
background image

MPC555

 / 

MPC556

DEVELOPMENT SUPPORT

MOTOROLA

USER’S MANUAL

Rev. 15 October  2000

21-13

• Both “go to x” and “continue” working modes are supported for the instruction

breakpoints.

21.3.1.1 Restrictions

There are cases when the same watchpoint can be detected more than once during
the execution of a single instruction, e.g. a load/store watchpoint is detected on more
than one transfer when executing a load/store multiple/string or a load/store watch-
point is detected on more than one byte when working in byte mode. In all these cases
only one watchpoint of the same type is reported for a single instruction. Similarly, only
one watchpoint of the same type can be counted in the counters for a single instruc-
tion.

Since watchpoint events are reported upon the retirement of the instruction that
caused the event, and more than one instruction can retire from the machine in one
clock, consequent events may be reported in the same clock. Moreover the same
event, if detected on more than one instruction (e.g., tight loops, range detection), in
some cases will be reported only once. Note that the internal counters count correctly
in these cases.

Do not put a breakpoint on an 

mtspr ICTRL

 instruction. When a breakpoint is set on

an 

mtspr ICTRL

 Rx instruction and the value of bit 28 (IFM) is one, the result will be

unpredictable. A breakpoint can be taken or not on the instruction and the value of the
IFM bit can be either zero or one. Also, do not put a breakpoint on an mtspr ICTRL Rx
instruction when Rx contains one in bit 28.

21.3.1.2 Byte and Half-Word Working Modes

The CPU watchpoints and breakpoints support enables the user to detect matches on
bytes and half-words even when accessed using a load/store instruction of larger data
widths, for example when loading a table of bytes using a series of load word instruc-
tions. In order to use this feature, the user needs to program the byte mask for each
of the L-data comparators and to write the needed match value to the correct half-word
of the data comparator when working in half-word mode and to the correct bytes of the
data comparator when working in byte mode.

Since bytes and half-words can be accessed using a larger data width instruction, it is
impossible for the user to predict the exact value of the L-address lines when the re-
quested byte/half-word is accessed, (e.g., if the matched byte is byte two of the word
and it is accessed using a load word instruction), the L-address value will be of the
word (byte zero). Therefore, the CPU masks the two least-significant bits of the L-ad-
dress comparators whenever a word access is performed and the least-significant bit
whenever a half-word access is performed.

Address range is supported only when aligned according to the access size. (See ex-
amples)

 

   

  

F

re

e

sc

a

le

 S

e

m

ic

o

n

d

u

c

to

r,

 I

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

 

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

n

c

.

..

Summary of Contents for MPC555








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC555

MYiR MYC-C8MMQ6-8E2D-160-I Linux Development Manual preview
MYC-C8MMQ6-8E2D-160-I
Brand: MYiR Pages: 50
JETWAY NF9U-F Technical Manual preview
NF9U-F
Brand: JETWAY Pages: 52
Intel BLKDP55WG - P55 LG1156 MAX-16 GB DDR3 ATX Motherboard Technical Product Specification preview
BLKDP55WG - P55 LG1156 MAX-16 GB DDR3 ATX Motherboard
Brand: Intel Pages: 88
NXP Semiconductors MPT612 User Manual preview
MPT612
Brand: NXP Semiconductors Pages: 269
MSI Z270 Gaming Pro Carbon Motherboard User Manual preview
Z270 Gaming Pro Carbon Motherboard
Brand: MSI Pages: 92
NXP Semiconductors MSC8156ADS Quick Start Manual preview
MSC8156ADS
Brand: NXP Semiconductors Pages: 2
Gigabyte GA-C847N-D User Manual preview
GA-C847N-D
Brand: Gigabyte Pages: 44
Benezan Electronics Beamicon2Basic Installation Manual preview
Beamicon2Basic
Brand: Benezan Electronics Pages: 18
Biostar U8668 D Bios Setup Manual preview
U8668 D
Brand: Biostar Pages: 32
Systium Technologies Ready 113 User'S Quick Start Manual preview
Ready 113
Brand: Systium Technologies Pages: 4
Biostar Z690 VALKYRIE Manual preview
Z690 VALKYRIE
Brand: Biostar Pages: 210
IEI Technology WAFER - E668EV ATX User Manual preview
WAFER - E668EV ATX
Brand: IEI Technology Pages: 59
S&T 44011-0208-13-2 User Manual preview
44011-0208-13-2
Brand: S&T Pages: 65
YASKAWA ANTAIOS User Manual preview
ANTAIOS
Brand: YASKAWA Pages: 28
e2v AT84CS001-EB User Manual preview
AT84CS001-EB
Brand: e2v Pages: 39
Quanmax ATX-KLS0 Series User Manual preview
ATX-KLS0 Series
Brand: Quanmax Pages: 69
AOpen DX3R-U Easy Installation Manual preview
DX3R-U
Brand: AOpen Pages: 8
IEPC EPC9179 Quick Start Manual preview
EPC9179
Brand: IEPC Pages: 9

Brands by name

Popular brands

Load more brands