manualshive.com logo in svg

NXP Semiconductors MPC555, User Manual

The NXP Semiconductors MPC555 is a cutting-edge microcontroller designed for versatile applications. Enhance your product development experience with our comprehensive User Manual, available for free download at manualshive.com. Discover detailed instructions and unleash the full potential of the MPC555 to transform your projects.

Share
Download
background image

MPC555

 / 

MPC556

QUEUED ANALOG-TO-DIGITAL CONVERTER MODULE-64

MOTOROLA

USER’S MANUAL

Rev. 15 October  2000

13-8

current effect of mid-level signals on the inputs used for analog signals. Digital input
signals must meet the input low voltage (VIL) or input high voltage (VIH) specifications.
If an analog input pin does not meet the digital input pin specifications when a digital
port read operation occurs, an indeterminate state is read. To avoid reading inappro-
priate values on analog inputs, the user software should employ a “masking” opera-
tion.

During a port data register read, the actual value of the pin is reported when its corre-
sponding bit in the data direction register defines the pin to be an input (port A only).
When the data direction bit specifies the pin to be an output, the content of the port
data register is read. By reading the latch which drives the output pin, software instruc-
tions that read data, modify it, and write the result, like bit manipulation instructions,
work correctly.

There is one special case to consider for digital I/O port operation. When the MUX (ex-
ternally multiplexed) bit is set in QACR0, the data direction register settings are ig-
nored for the bits corresponding to PQA[2:0], the three multiplexed address MA[2:0]
output pins. The MA[2:0] pins are forced to be digital outputs, regardless of the data
direction setting, and the multiplexed address outputs are driven. The data returned
during a port data register read is the value of the multiplexed address latches which
drive MA[2:0], regardless of the data direction setting.

13.6.1 Port Data Register

QADC64 ports A and B are accessed through two 8-bit port data registers (PORTQA
and PORTQB). Port A pins are referred to as PQA when used as an 8-bit input/output
port. Port A can also be used for analog inputs AN[59:52] and external multiplexer ad-
dress outputs MA[2:0].

Port B pins are referred to as PQB when used as an 8-bit input-only digital port. Port
B can also be used for non-multiplexed AN[51:48]/AN[3:0] and multiplexed ANz, ANy,
ANx, ANw analog inputs.

PORTQA and PORTQB are unaffected by reset. Refer to 

13.12.4 Port A/B Data Reg-

ister

 for register and bit descriptions.

13.6.2 Port Data Direction Register

The port data direction register (DDRQA) is associated with the port A digital I/O pins.
These bi-directional pins may have somewhat higher leakage and capacitance speci-
fications. 

Any bit in this register set to one configures the corresponding pin as an output. Any
bit in this register cleared to zero configures the corresponding pin as an input. Soft-
ware is responsible for ensuring that DDRQA bits are not set to one on pins used for
analog inputs. When a DDRQA bit is set to one and the pin is selected for analog con-
version, the voltage sampled is that of the output digital driver as influenced by the
load.

NOTE

 

   

  

F

re

e

sc

a

le

 S

e

m

ic

o

n

d

u

c

to

r,

 I

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

 

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

n

c

.

..

Summary of Contents for MPC555








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC555

Microsemi VSC8584 User Manual preview
VSC8584
Brand: Microsemi Pages: 15
Tews Technologies TVME220 Series User Manual preview
TVME220 Series
Brand: Tews Technologies Pages: 26
Mikroe CLICKER 4 for STM32 User Manual preview
CLICKER 4 for STM32
Brand: Mikroe Pages: 16
Supermicro C9Z490-PG User Manual preview
C9Z490-PG
Brand: Supermicro Pages: 142
Xilinx SP605 Hardware User'S Manual preview
SP605
Brand: Xilinx Pages: 70
Alpha Data ADM-PCIE-9V3 User Manual preview
ADM-PCIE-9V3
Brand: Alpha Data Pages: 40
Ideal-Standard A 961 765 NU Operating Instructions Manual preview
A 961 765 NU
Brand: Ideal-Standard Pages: 20
ASROCK P55 DELUXE3 - Installation Manual preview
P55 DELUXE3 -
Brand: ASROCK Pages: 226
OLIMEX ADuC-MT7020 User Manual preview
ADuC-MT7020
Brand: OLIMEX Pages: 13
Infineon BCM943362WCD2 User Manual preview
BCM943362WCD2
Brand: Infineon Pages: 11
Qiyangtech QY-9263S Hardware Manual preview
QY-9263S
Brand: Qiyangtech Pages: 16
JETWAY 618TAF User Manual preview
618TAF
Brand: JETWAY Pages: 56
Embedian SBC-SMART-MEN User Manual preview
SBC-SMART-MEN
Brand: Embedian Pages: 70
Yamaha 90A Owner'S Manual preview
90A
Brand: Yamaha Pages: 82
ECS P6VXM2 Manual preview
P6VXM2
Brand: ECS Pages: 87
Gigabyte GA-EP41-UD3L User Manual preview
GA-EP41-UD3L
Brand: Gigabyte Pages: 88
Texas Instruments ADS54J42 User Manual preview
ADS54J42
Brand: Texas Instruments Pages: 22
PC Chips M598LMR User Manual preview
M598LMR
Brand: PC Chips Pages: 49

Brands by name

Popular brands

Load more brands