manualshive.com logo in svg

NXP Semiconductors MPC555, User Manual

The NXP Semiconductors MPC555 is a cutting-edge microcontroller designed for versatile applications. Enhance your product development experience with our comprehensive User Manual, available for free download at manualshive.com. Discover detailed instructions and unleash the full potential of the MPC555 to transform your projects.

Share
Download
background image

MPC555

 / 

MPC556

CENTRAL PROCESSING UNIT

MOTOROLA

USER’S MANUAL

Rev. 15 October  2000

3-49

Execution resumes at offset 0x01000 from the base address indicated by MSR

IP

.

3.15.4.13 Implementation-Specific Instruction Storage Protection Error Interrupt

The implementation-specific instruction storage protection error interrupt occurs in the
following cases:

• The fetch access violates storage protection.
• The fetch access is to guarded storage and MSR

IR 

= 1.

The following registers are set:

Register Name

Bits

Description

Save/Restore Register 0 (SRR0)

Set to the effective address of the instruction that caused the 
interrupt

Save/Restore Register 1 (SRR1)

1:4

Set to 0

10:15

Set to 0

Other

Loaded from bits 16:31 of MSR. In the current implementa-
tion, Bit 30 of the SRR1 is never cleared, except by loading a 
zero value from MSR

RI

Machine State Register (MSR)

IP

No change

ME

No change

LE

Bit is copied from ILE

Other

Set to 0

 

   

  

F

re

e

sc

a

le

 S

e

m

ic

o

n

d

u

c

to

r,

 I

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  

 

Freescale Semiconductor, Inc.

For More Information On This Product,

   Go to: www.freescale.com

n

c

.

..

Summary of Contents for MPC555








































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC555

ST STM32 Nucleo-32 User Manual preview
STM32 Nucleo-32
Brand: ST Pages: 37
Xilinx ML505 Getting Started Tutorial preview
ML505
Brand: Xilinx Pages: 31
BESTEK BNX-M87 User Manual preview
BNX-M87
Brand: BESTEK Pages: 45
Epcom EPC9058 Quick Start Manual preview
EPC9058
Brand: Epcom Pages: 8
IEI Technology NANO-BT Series User Manual preview
NANO-BT Series
Brand: IEI Technology Pages: 145
Micrel MIC24056 Manual preview
MIC24056
Brand: Micrel Pages: 10
HONDA marine BF135 Wiring Diagram preview
BF135
Brand: HONDA marine Pages: 2
Supermicro X11SCE-F User Manual preview
X11SCE-F
Brand: Supermicro Pages: 95
BCM GT440ZX User Manual preview
GT440ZX
Brand: BCM Pages: 57
Gigabyte GA-M52S-S3P User Manual preview
GA-M52S-S3P
Brand: Gigabyte Pages: 96
Daewoo CB656M-WH User Manual preview
CB656M-WH
Brand: Daewoo Pages: 39
Gigabyte AMD785G Manual preview
AMD785G
Brand: Gigabyte Pages: 53
SOLTEK SL-75ERV User Manual preview
SL-75ERV
Brand: SOLTEK Pages: 94
ASROCK E3C224D2I User Manual preview
E3C224D2I
Brand: ASROCK Pages: 65
NXP Semiconductors SJA1105SMBEVM User Manual preview
SJA1105SMBEVM
Brand: NXP Semiconductors Pages: 35
NXP Semiconductors LFSTBEB7361 Quick Start Manual preview
LFSTBEB7361
Brand: NXP Semiconductors Pages: 2
Gigabyte GA-946GZ-DS3 User Manual preview
GA-946GZ-DS3
Brand: Gigabyte Pages: 80
Wave Mate Z80 Super Bullet Manual preview
Z80 Super Bullet
Brand: Wave Mate Pages: 25

Brands by name

Popular brands

Load more brands