manualshive.com logo in svg

NXP Semiconductors MCF5272 ColdFire, User Manual, Page: 73 / 545

Share
Download
NXP Semiconductors MCF5272 ColdFire User Manual Download Page 73

ColdFire Core

MCF5272 ColdFire

®

 Integrated Microprocessor User’s Manual, Rev. 3

Freescale Semiconductor

2-5

 

Figure 2-3. ColdFire Programming Model

2.2.1.1

Data Registers (D0–D7) 

Registers D0–D7 are used as data registers for bit, byte (8-bit), word (16-bit), and longword (32-bit) 
operations. They may also be used as index registers.

2.2.1.2

Address Registers (A0–A6) 

The address registers (A0–A6) can be used as software stack pointers, index registers, or base address 
registers and may be used for word and longword operations.

2.2.1.3

Stack Pointer (A7, SP)

The processor core supports a single hardware stack pointer (A7) used during stacking for subroutine calls, 
returns, and exception handling. The stack pointer is implicitly referenced by certain operations and can 
be explicitly referenced by any instruction specifying an address register. The initial value of A7 is loaded 

31

0

D0

Data registers

D1
D2
D3
D4
D5
D6
D7

31

0

A0

Address registers

A1
A2
A3
A4
A5
A6
A7

Stack pointer

PC

Program counter

CCR

Condition code register

31

0

MACSR

MAC status register

ACC

MAC accumulator

MASK

MAC mask register

15

31

19

(CCR)

SR

Status register

Must be zeros

VBR

Vector base register

CACR

Cache control register

ACR0

Access control register 0 

ACR1

Access control register 1 

ROMBAR

ROM base address register

RAMBAR

RAM base address register

MBAR

Module base address register

User Regi

ste

rs

Super

visor

 Re

gisters

Summary of Contents for MCF5272 ColdFire


































































































































































































































































































































































































































































































































































Reviews:

No comments