manualshive.com logo in svg

NXP Semiconductors MCF5272 ColdFire, User Manual

Share
Download
NXP Semiconductors MCF5272 ColdFire User Manual Download Page 218

DMA Controller

MCF5272 ColdFire

®

 Integrated Microprocessor User’s Manual, Rev. 3

10-6

Freescale Semiconductor

 

10.3.4

DMA Destination Address Register (DDAR)

The DDAR provides a 32-bit address that the DMA controller drives onto the internal address bus for all 
of the channel’s write accesses. The address is altered after each write access according to the addressing 
mode.

10.3.5

DMA Byte Count Register (DBCR)

The DBCR is initially loaded with the number of bytes to be transferred during the DMA. After each 
transfer, the DBCR decrements by the number of bytes transferred. DIR[ASC] is set when the byte counter 
reaches zero. The user must ensure that the bytes remaining to be transferred and the transfer size are such 
that the byte counter decrements to zero or wraps around without setting the ASC flag.

  

31

 0

 Field

DESTADR

 Reset

0000_0000_0000_0000_0000_0000_0000_0000

 R/W

R/W

 Addr

MBAR + 0x00F0

Figure 10-4. DMA Destination Address Register (DDAR)

 31

24 23

 0

 Field

—

BYTCNT

 Reset

R/W

 R/W

0000_0000_0000_0000_0000_0000_0000_0000

 Addr

MBAR + 0x00E8

Figure 10-5. DMA Byte Count Register (DBCR)

Summary of Contents for MCF5272 ColdFire


































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands