manualshive.com logo in svg

NXP Semiconductors MC9S12XS128, Reference Manual

The NXP Semiconductors MC9S12XS128 microcontroller offers a wide range of features and capabilities. To unlock its full potential, we provide a comprehensive Reference Manual that can be downloaded for free from our website. This manual guides users through the product's functionalities and ensures optimal utilization.

Share
Download
background image

Port Integration Module (S12XSPIMV1)

S12XS Family Reference Manual, Rev. 1.13

Freescale Semiconductor

83

2.3.14

IRQ Control Register (IRQCR)

2.3.15

PIM Reserved Register PIMTEST

1

This register is reserved for factory testing of the PIM module and is not available in normal operation.
Writing to this register when in special modes can alter the pin functionality.

 Address 0x001E

Access: User read/write

1

1

Read: See individual bit descriptions below
Write: See individual bit descriptions below

7

6

5

4

3

2

1

0

R

IRQE

IRQEN

0

0

0

0

0

0

W

Reset

0

1

0

0

0

0

0

0

= Unimplemented or Reserved

Figure 2-12. IRQ Control Register (IRQCR)

Table 2-13. IRQCR Register Field Descriptions

Field

Description

7

IRQE

IRQ select edge sensitive only—
Special mode: Read or write anytime
Normal mode: Read anytime, write once

1 IRQ configured to respond only to falling edges. Falling edges on the IRQ pin will be detected anytime IRQE=1

and will be cleared only upon a reset or the servicing of the IRQ interrupt.

0 IRQ configured for low level recognition.

6

IRQEN

IRQ enable—
Read or write anytime

1 IRQ pin is connected to interrupt logic.
0 IRQ pin is disconnected from interrupt logic.

1. Implementation pim_xe.01.01 and later

 Address 0x001F

Access: User read

1

7

6

5

4

3

2

1

0

R

0

0

0

0

0

0

0

0

W

Reset

0

0

0

0

0

0

0

0

= Unimplemented or Reserved

Figure 2-13. PIM Reserved Register

Summary of Contents for MC9S12XS128




































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S12XS128

ABATEC A1 Installation And Operation Instruction Manual preview
A1
Brand: ABATEC Pages: 8
wattio AIR Read Me preview
AIR
Brand: wattio Pages: 20
3M PX5 Series Reference Manual preview
PX5 Series
Brand: 3M Pages: 34
ECKELMANN VS 3010 BS Operating Instruction preview
VS 3010 BS
Brand: ECKELMANN Pages: 178
H3C WX Series Registration And Activation Manual preview
WX Series
Brand: H3C Pages: 17
H3C WX Series Getting Started Manual preview
WX Series
Brand: H3C Pages: 32
Taco Electronic Solutions iWorx MPU2 Installation Manual preview
iWorx MPU2
Brand: Taco Electronic Solutions Pages: 28
LEGRAND Arteor 5 742 74 Quick Start Manual preview
Arteor 5 742 74
Brand: LEGRAND Pages: 2
Xylem Aquavar IPC Quick Start Manual preview
Aquavar IPC
Brand: Xylem Pages: 28
Overland Storage NEO 2000e Remove & Replace Instructions preview
NEO 2000e
Brand: Overland Storage Pages: 4
NEC mPD789101 User Manual preview
mPD789101
Brand: NEC Pages: 265
National Instruments PXI-8232 Installation Manual preview
PXI-8232
Brand: National Instruments Pages: 8
TIE AMBITECH BRAKE-PAK Installation & Setup Instructions preview
AMBITECH BRAKE-PAK
Brand: TIE Pages: 5
Midian Electronics TRC-2 Manual preview
TRC-2
Brand: Midian Electronics Pages: 22
Davey Torrium2 Installation And Operating Instructions Manual preview
Torrium2
Brand: Davey Pages: 8
Danfoss AK-PC 772A User Manual preview
AK-PC 772A
Brand: Danfoss Pages: 118
Botex DMX DC-136 User Manual preview
DMX DC-136
Brand: Botex Pages: 36
ADLINK Technology cPCI-7252 User Manual preview
cPCI-7252
Brand: ADLINK Technology Pages: 54

Brands by name

Popular brands

Load more brands