manualshive.com logo in svg

NXP Semiconductors MC9S12VRP64, Owner Reference Manual

The NXP Semiconductors MC9S12VRP64 is a premium microcontroller ideal for various applications. With our user-friendly Owner Reference Manual, you can effortlessly navigate through the device's features and functionalities. Download this comprehensive manual for free from our website manualshive.com, enabling you to harness the full potential of this exceptional product.

Share
Download
background image

Interrupt Module (S12SINTV1)

MC9S12VRP Family Reference Manual Rev. 1.3 

NXP Semiconductors

239

Figure 7-1. INT Block Diagram

7.2

External Signal Description

The INT module has no external signals.

7.3

Memory Map and Register Definition

This section provides a detailed description of all registers accessible in the INT module.

7.3.1

Register Descriptions

This section describes in address order all the INT registers and their individual bits.

7.3.1.1

Interrupt Vector Base Register (IVBR)

Read: Anytime

Write: Anytime

Address: 0x0120

 

7

6

5

4

3

2

1

0

R

IVB_ADDR[7:0]

W

Reset

1

1

1

1

1

1

1

1

Figure 7-2. Interrupt Vector Base Register (IVBR)

Wake Up

IVBR

Interrupt

Requests

Interrupt Requests

CPU

Vector

Address

Peripheral

To

 C

P

U

Pr

io

rit

y

Decoder

Non I bit Maskable Channels

I bit Maskable Channels

Summary of Contents for MC9S12VRP64












































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MC9S12VRP64

Maestra 8080 User Manual preview
8080
Brand: Maestra Pages: 22
Eaton S701 Instruction Leaflet preview
S701
Brand: Eaton Pages: 8
Daihan Scientific WHM-C10D Operation Manual preview
WHM-C10D
Brand: Daihan Scientific Pages: 11
Varian Turbo-V 250 series Instruction Manual preview
Turbo-V 250 series
Brand: Varian Pages: 79
Xilinx ML410 User Manual preview
ML410
Brand: Xilinx Pages: 101
Fairford Synergy SGY-101 Quick Start Manual preview
Synergy SGY-101
Brand: Fairford Pages: 20
ST UM1932 User Manual preview
UM1932
Brand: ST Pages: 40
Varian 969-9507 Instruction Manual preview
969-9507
Brand: Varian Pages: 37
LAMBERTI ELEKTRONIK Latherm HZR Comfort Operating Manual preview
Latherm HZR Comfort
Brand: LAMBERTI ELEKTRONIK Pages: 16
3M Touch Screen Controller SX112 Reference Manual preview
Touch Screen Controller SX112
Brand: 3M Pages: 33
Parker P3HPA Series Manual preview
P3HPA Series
Brand: Parker Pages: 22
Aube Technologies TH146-N-U Installation Manual preview
TH146-N-U
Brand: Aube Technologies Pages: 12
NEEDO MY NEEDO User Manual Book preview
MY NEEDO
Brand: NEEDO Pages: 193
Danfoss ADAP-KOOL AK-CC 750 Service Manual preview
ADAP-KOOL AK-CC 750
Brand: Danfoss Pages: 6
Berker 85865100 Operation Instructions preview
85865100
Brand: Berker Pages: 2
S&C GridMaster Installation Manual preview
GridMaster
Brand: S&C Pages: 16
Datapath iolite 600 Quick Start Manual preview
iolite 600
Brand: Datapath Pages: 16
Qanon VDA14 Manual preview
VDA14
Brand: Qanon Pages: 10

Brands by name

Popular brands

Load more brands