NXP Semiconductors LPC5410x User Manual Download Page 94

Page: 94 / 463

UM10850

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 2.4 — 13 September 2016

95 of 464

NXP Semiconductors

UM10850

Chapter 7: LPC5410x I/O pin configuration (IOCON)

[2]

The input may be turned off by clearing DIGIMODE if it is not needed.

7.5.3 Type A IOCON registers (PIO0, PIO1)

This IOCON table applies to pins P0[29 to 31], P1[0 to 8].

Table 114. Type I I/O Control registers: FUNC values and pin functions

Value of FUNC field in IOCON register

Register

000

001

010

011

100

101

110

111

PIO0_23

I2C0_SCL

CT32B0_CAP0

PIO0_24

I2C0_SDA

CT32B0_CAP1

CT32B0_MAT0

PIO0_25

I2C1_SCL

U1_CTS

CT32B0_CAP2

CT32B1_CAP1

PIO0_26

I2C1_SDA

CT32B0_CAP3

PIO0_27

I2C2_SCL

CT32B2_CAP0

PIO0_28

I2C2_SDA

CT32B2_MAT0

Table 115. Address map PIO0_[29:31] registers

Peripheral

Base address

Offset

Increment

Dimension

IOCON

0x4001 C000

[0x074:0x07C]

0x4

Table 116. Type A IOCON registers(PIO0_[29:31], address offsets [0x074:0x07C]) bit description

Bit

Symbol

Value

Description

Reset
value

2:0

FUNC

Selects pin function.

4:3

MODE

Selects function mode (on-chip pull-up/pull-down resistor control).

0x0

Inactive. Inactive (no pull-down/pull-up resistor enabled).

0x1

Pull-down. Pull-down resistor enabled.

0x2

Pull-up. Pull-up resistor enabled.

0x3

Repeater. Repeater mode.

Reserved. Read value is undefined, only zero should be written.

INVERT

Input polarity.

Disabled. Input function is not inverted.

Enabled. Input is function inverted.

DIGIMODE

Select Analog/Digital mode.

Analog mode.

Digital mode.

FILTEROFF

Controls input glitch filter.

Filter enabled. Noise pulses below approximately 10 ns are filtered out

Filter disabled. No input filtering is done

Reserved. Read value is undefined, only zero should be written.

Summary of Contents for LPC5410x
















































































































































































































































































































































































































































































Search results

Summary of Contents for LPC5410x

Reviews:

NXP Semiconductors LPC5410x, User Manual, Page: 94 / 463

Search results

Summary of Contents for LPC5410x

Reviews: