manualshive.com logo in svg

NXP Semiconductors LPC5410x, User Manual, Page: 80 / 463

Share
Download
NXP Semiconductors LPC5410x User Manual Download Page 80

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

81 of 464

NXP Semiconductors

UM10850

Chapter 5: LPC5410x Power Management

•

The power API provides an easy way to optimize power consumption depending on 
CPU load and performance requirements. See 

Chapter 30 “LPC5410x Power 

profiles/Power control API”

.

5.3.3 Sleep mode

In Sleep mode, the system clock to the CPU is stopped and execution of instructions is 
suspended until either a reset or an interrupt occurs.

Peripheral functions, if selected to be clocked in the AHBCLKCTRL registers, continue 
operation during Sleep mode and may generate interrupts to cause the processor to 
resume execution. Sleep mode eliminates dynamic power used by the processor itself, 
memory systems and related controllers, and internal buses. The processor state and 
registers, peripheral registers, and internal SRAM values are maintained, and the logic 
levels of the pins remain static.

As in active mode, the power API provides an easy way to optimize power consumption 
depending on CPU load and performance requirements in sleep mode. See 

Section 30.4.3 “Chip_POWER_EnterPowerMode”

.

5.3.3.1 Power configuration in Sleep mode

Power consumption in Sleep mode is configured by the same settings as in Active mode:

•

The clock remains running.

•

The system clock frequency remains the same as in Active mode, but the processor is 
not clocked.

•

Analog and digital peripherals are powered and selected as in Active mode through 
the PDRUNCFG, AHBCLKCTRL0, AHBCLKCTRL1 registers.

5.3.3.2 Programming Sleep mode

The following steps must be performed to enter Sleep mode:

1. In the NVIC, enable all interrupts that are needed to wake up the part.

2. Call power API: 

pPWRD->power_mode_configure(SLEEP, peripheral);

Remark: 

The 

peripheral

 parameter is don’t care.

3. Execute the Wait-For-Interrupt (WFI) instruction.

5.3.3.3 Wake-up from Sleep mode

Sleep mode is exited automatically when an interrupt enabled by the NVIC arrives at the 
processor or a reset occurs. After wake-up caused by an interrupt, the device returns to its 
original power configuration defined by the contents of the PDRUNCFG and the 
AHBCLKCTRL registers. If a reset occurs, the microcontroller enters the default 
configuration in Active mode.

5.3.4 Deep-sleep mode

In Deep-sleep mode, the system clock to the processor is disabled as in Sleep mode. All 
analog blocks are powered down by default but can be selected to keep running through 
the power API if needed as wake-up sources. The main clock, and therefore all peripheral 
clocks, are disabled. The IRC is disabled. The flash is in stand-by mode.

Summary of Contents for LPC5410x
















































































































































































































































































































































































































































































Reviews:

No comments