NXP Semiconductors LPC11U1x User Manual Download | Manualshive

Page: 348 / 523

background image

UM10462

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 5.5 — 21 December 2016

348 of 523

NXP Semiconductors

UM10462

Chapter 15: LPC11U3x/2x/1x 16-bit counter/timers CT16B0/1

15.7.13 Rules for single edge controlled PWM outputs

1. All single edge controlled PWM outputs go LOW at the beginning of each PWM cycle

(timer is set to zero) unless their match value is equal to zero.

2. Each PWM output will go HIGH when its match value is reached. If no match occurs

(i.e. the match value is greater than the PWM cycle length), the PWM output remains
continuously LOW.

3. If a match value larger than the PWM cycle length is written to the match register, and

the PWM signal is HIGH already, then the PWM signal will be cleared on the next start
of the next PWM cycle.

4. If a match register contains the same value as the timer reset value (the PWM cycle

length), then the PWM output will be reset to LOW on the next clock tick. Therefore,
the PWM output will always consist of a one clock tick wide positive pulse with a
period determined by the PWM cycle length (i.e. the timer reload value).

5. If a match register is set to zero, then the PWM output will go to HIGH the first time the

timer goes back to zero and will stay HIGH continuously.

Note:

When the match outputs are selected to perform as PWM outputs, the timer reset

(MRnR) and timer stop (MRnS) bits in the Match Control Register MCR must be set to
zero except for the match register setting the PWM cycle length. For this register, set the
MRnR bit to one to enable the timer reset when the timer value matches the value of the
corresponding match register.

3

PWMEN3

PWM mode enable for channel3.

0

0

CT16Bn_MAT3 is controlled by EM3.

1

PWM mode is enabled for CT16Bn_MAT3.

31:4

-

Reserved, user software should not write ones to
reserved bits. The value read from a reserved bit is
not defined.

-

Table 314. PWM Control Register (PWMC, address 0x4000 C074 (CT16B0) and 0x4001 0074

(CT16B1)) bit description

Bit

Symbol

Value

Description

Reset
value

Fig 56. Sample PWM waveforms with a PWM cycle length of 100 (selected by MR2) and

MAT2:0 enabled as PWM outputs by the PWMC register.

100

(counter is reset)

0

41

65

PWM0/MAT0

PWM1/MAT1

PWM2/MAT2

MR2 = 100

MR1 = 41

MR0 = 65

«
...
346
347
348
349
350
...
»

Summary of Contents for LPC11U1x












































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LPC11U1x

Brand: Samson Pages: 78

Brand: Rachio Pages: 16

Brand: ZKTeco Pages: 2

Brand: FASAR ELETTRONICA Pages: 2

Brand: Faro Pages: 3

Brand: YASKAWA Pages: 456

Brand: Talgil Pages: 14

Brand: Oriental motor Pages: 52

Brand: Opt Pages: 40

Brand: PI Pages: 111

Brand: Progeny Pages: 4

Brand: SUPMEA Pages: 40

ISaGRAF mPAC Series

Brand: ICP DAS USA Pages: 75

Brand: Zonet Pages: 2

Brand: Intrinsyc Pages: 38

Brand: Omron Pages: 157

Brand: Inner Range Pages: 28

ARES-1231 Series

Brand: Arbor Technology Pages: 94

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands