NXP Semiconductors LPC1102 User Manual Download | Manualshive

Page: 134 / 258

background image

UM10429

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2010. All rights reserved.

User manual

Rev. 1 — 20 October 2010

134 of 258

NXP Semiconductors

UM10429

Chapter 14: LPC1102 WatchDog Timer (WDT)

14.7.2 Watchdog Timer Constant register (WDTC - 0x4000 4004)

The WDTC register determines the time-out value. Every time a feed sequence occurs
the WDTC content is reloaded in to the Watchdog timer. It’s a 32-bit register with 8 LSB
set to 1 on reset. Writing values below 0xFF will cause 0x0000 00FF to be loaded to the
WDTC. Thus the minimum time-out interval is T

WDCLK

×

256

×

4.

14.7.3 Watchdog Feed register (WDFEED - 0x4000 4008)

Writing 0xAA followed by 0x55 to this register will reload the Watchdog timer with the
WDTC value. This operation will also start the Watchdog if it is enabled via the WDMOD
register. Setting the WDEN bit in the WDMOD register is not sufficient to enable the
Watchdog. A valid feed sequence must be completed after setting WDEN before the
Watchdog is capable of generating a reset. Until then, the Watchdog will ignore feed
errors. After writing 0xAA to WDFEED, access to any Watchdog register other than writing
0x55 to WDFEED causes an immediate reset/interrupt when the Watchdog is enabled.
The reset will be generated during the second PCLK following an incorrect access to a
Watchdog register during a feed sequence.

Interrupts should be disabled during the feed sequence. An abort condition will occur if an
interrupt happens during the feed sequence.

Table 131. Watchdog operating modes selection

WDEN

WDRESET

Mode of Operation

0

X (0 or 1)

Debug/Operate without the Watchdog running.

1

0

Watchdog interrupt mode: debug with the Watchdog interrupt but no
WDRESET enabled.

When this mode is selected, a watchdog counter underflow will set the
WDINT flag and the Watchdog interrupt request will be generated.

Remark:

In interrupt mode, check the WDINT flag. If this flag is set,

the interrupt is true and can be serviced by the interrupt routine. If this
flag is not set, the interrupt should be ignored.

1

1

Watchdog reset mode: operate with the Watchdog interrupt and
WDRESET enabled.

When this mode is selected, a watchdog counter underflow will reset
the microcontroller. Although the Watchdog interrupt is also enabled in
this case (WDEN = 1) it will not be recognized since the watchdog
reset will clear the WDINT flag.

Table 132. Watchdog Constant register (WDTC - address 0x4000 4004) bit description

Bit

Symbol

Description

Reset Value

23:0

Count

Watchdog time-out interval.

0x0000 00FF

31:25

-

Reserved

-

Table 133. Watchdog Feed register (WDFEED - address 0x4000 4008) bit description

Bit

Symbol

Description

Reset Value

7:0

Feed

Feed value should be 0xAA followed by 0x55.

NA

31:8

-

Reserved

-

«
...
132
133
134
135
136
...
»

Summary of Contents for LPC1102



































































































































































































































































Reviews:

No comments

Related manuals for LPC1102

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

Brand: Wavetec Pages: 17

Brand: Calsense Pages: 9

Smart Controller

Brand: MaestroHome Pages: 10

Brand: Faulhaber Pages: 66

Brand: Uclear Pages: 40

Brand: National Instruments Pages: 6

NetLinx Integrated Controller NI-3100

Brand: AMX Pages: 2

total control MRX-10

Brand: Universal Remote Control Pages: 16

Brand: D+H Pages: 20

Brand: CLS Pages: 6

Brand: Parker Pages: 22

Brand: Hanna Instruments Pages: 16

Brand: Mesto Pages: 12

Brand: Famco Pages: 113

Brand: Delta Pages: 313

Meridian MEC-110

Brand: FASTRON. Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands