manualshive.com logo in svg

NXP Semiconductors LCP43 Series, User Manual

Share
Download
NXP Semiconductors LCP43 Series User Manual Download Page 488

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2012. All rights reserved.

User manual

Rev. 1.3 — 6 July 2012 

488 of 1269

NXP Semiconductors

UM10503

Chapter 21: LPC43xx External Memory Controller (EMC)

[1]

Extended wait and page mode cannot be selected simultaneously.

[2]

EMC may perform burst read access even when the buffer enable bit is cleared.

21.7.22 Static Memory Write Enable Delay registers 

The StaticWaitWen registers enable you to program the delay from the chip select to the 
write enable. It is recommended that these registers are modified during system 
initialization, or when there are no current or outstanding transactions. This can be 
ensured by waiting until the EMC is idle, and then entering low-power, or disabled mode. 
These registers are accessed with one wait state.

 

21.7.23 Static Memory Output Enable Delay registers 

The StaticWaitOen registers enable you to program the delay from the chip select or 
address change, whichever is later, to the output enable. It is recommended that these 
registers are modified during system initialization, or when there are no current or 
outstanding transactions. This can be ensured by waiting until the EMC is idle, and then 
entering low-power, or disabled mode. These registers are accessed with one wait state.

20

P

Write protect.

0

0

Writes not protected (POR reset value).

1

Write protected.

31:21 -

-

Reserved, user software should not write ones to reserved bits. 
The value read from a reserved bit is not defined.

-

Table 375. Static Memory Configuration registers (STATICCONFIG[0:3], address 0x4000 5200 

(STATICCONFIG0), 0x4000 5220 (STATICCONFIG1), 0x4000 5240 
(STATICCONFIG2), 0x4000 5260 (STATICCONFIG3)) bit description

Bit

Symbol

Value Description

Reset 
value

Table 376. Static Memory Write Enable Delay registers (STATICWAITWEN[0:3], address 

0x4000 5204 (STATICWAITWEN0), 0x4000 5224 (STATICWAITWEN1), 0x4000 5244 
(STATICWAITWEN2), 0x4000 5264 (STATICWAITWEN3)) bit description

Bit

Symbol

Description

Reset 
value

3:0

WAITWEN

Wait write enable.
Delay from chip select assertion to write enable.
0x0 = One CCLK cycle delay between assertion of chip select and 
write enable (POR reset value).
0x1 - 0xF = (n + 1) CCLK cycle delay. The delay is (W1) x 
tCCLK.

0x0

31:4

-

Reserved, user software should not write ones to reserved bits. The 
value read from a reserved bit is not defined.

-

Summary of Contents for LCP43 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands